ToolBox

Toolbox Nmea output


Toolbox Nmea output

Toolbox Nmea Output

How to Enable NMEA Output for a Third-Party Device

  1. Open Toolbox.

  2. Go to the NMEA Output tab.

  3. Take the required connection parameters from the third-party device (for example: baud rate and supported NMEA messages).

  4. Fill in the fields in the NMEA Output settings:

    • Baud rate

    • GGA

    • RMC

    • VTG

    • GST

    • ZDA

    • GSA

    • GSV

  5. After all parameters are configured, turn on the NMEA Output switch.

  6. The device will start sending NMEA data to the external device.

image.png


Deadband Calibration

Deadband calibration determines the minimum steering angle at which the front wheels start to move. This value must be measured and then saved in the tractor parameters in the Fieldbee application.

Preparation

Before starting calibration:

  1. Warm up the engine and hydraulic system.
    The hydraulic steering system must be operating under normal conditions.
  2. Park the tractor on a flat surface.
  3. Straighten the front wheels.
  4. Exit the cabin and stand near the front wheels so you can clearly see the moment when they begin to move.

Calibration Procedure

  1. Open Toolbox in the application.
  2. Tap PowerSteer, then tap your Device ID.
  3. Go to the PowerWheel tab, wait tha app read PowerWheel parameters.
  4. Press tab Deadband calibration.

Screenshot_20260317-130252.png

  1. Press Start for start calibration.
  2. Slowly change the steering angle using the - / + controls.
  3. Carefully watch the front wheels and identify the minimum steering angle at which the wheels begin to move.

Screenshot_20260317-130300.png

  1. When the wheels just start moving, note the deadband value (°) shown in the application.
  2. Press Finish to complete the calibration.

Screenshot_20260317-130312.png

After determining the deadband value, copy it for move to Fieldbee navigation app.

  1. Near calibration value tap Copy button.

Screenshot_20260317-130325.png

Using the Deadband Value

  1. Open the Fieldbee navigation application.
  2. Go to Record Keeping> Vehicles.
  3. Find Calibrated tracktor and tap Edit.
  4. Tap the tractor angle field 8 times to open the Advanced Menu.

Correction.Fix type

image.png

Quick Guide: Fix Type Selection

The auto-steer will work strictly only on the exact modes you select. You can select just one or multiple options:

(Don't forget to press Set to apply your choices).

What does this setting mean?

Selecting a specific "Fix type" establishes the minimum acceptable accuracy threshold for your navigation.

Simply put, you are telling the system: "Only allow the tractor to drive on auto-steer (turn the steering wheel) when the RTK signal quality is equal."

If the signal quality drops below your chosen level (for example, you drive under thick trees or lose the mobile internet connection for your RTK), the system will automatically disengage the auto-steering. This ensures the tractor doesn't suddenly swerve and ruin the row.

How to choose the right setting in practice?

The Golden Rule: The more demanding and precise the field operation, the stricter your setting should be.

  1. For seeding, planting, and inter-row cultivation: You must select and apply the Set button at the RTK level. If the tractor suddenly loses the perfect signal and drops down to FRTK mode, the steering wheel will immediately disengage, prompting you to take manual control. This strictly protects your crops from being accidentally run over or cut out.

  2. For spraying, fertilizer spreading, discing, or plowing: You can lower the threshold to the FRTK (or sometimes even DGPS) level. In these operations, a 15-20 cm error is not critical. By setting the permission to FRTK, the auto-steering won't constantly disengage and kick you off the guidance line during brief interruptions of the RTK signal. This will save you a lot of time and nerves.

Ultimately, this menu allows you to find the perfect balance between maximum accuracy (where the system doesn't forgive even a single second of signal loss) and continuous steering operation (where a slight error is tolerated to keep the auto-steer engaged).

Correction.GNSS

image.png

 

Quick Guide: GNSS Constellation Selection

This setting determines which global satellite systems your receiver will track and use to calculate its position.

Unlike the "Fix type" menu, this is a single-choice list where you select a specific combination of satellite networks:

(Don't forget to press Set to apply your choice).

Correction(Bridge mode)

Quick Guide: Bridge Mode (Estimation allowed)

The Estimation allowed toggle switch enables a temporary fallback feature designed to help you cross minor signal dead-zones.

Correction(Source)

Quick Guide: Correction Source Selection

This setting determines the method your system uses to receive RTK correction data from the base station.

(Don't forget to press Set to apply your choice).

image.png

Deadband Auto Calibration

Location in toolbox: 
Tab Powerwheel open, waiting for motor parameters, motor should be in position mode to do Deadband Auto )>then tab Deadband Auto

Preparation

Before starting calibration:
Make sure that you have the correct firmware of the controller that supports this new function 2.7.8 firmware

  1. Warm up the engine and hydraulic system.
    The hydraulic steering system must be operating under normal conditions.
  2. Park the tractor on a flat surface.
  3. Straighten the front wheels.
  4. Follow and read instructions and pop-up windows from the toolbox.

How is correct and not correct installed  calibration sensor 

image.png


Wheel Calibration 0/2 means that calibration is not started 

After successfully completing the installation according to the instructions, click the Start button to begin auto-calibration for the first wheel.

After finishing calibration on the first wheel, move the sensor to the second wheel.
Wait 40 seconds to let the sensor stabilize and data settle, then press START to begin calibration on the second wheel.

image.png




After successful calibration, use the COPY button to save the deadband values and transfer them to the Navigation App in the tractor profile.

image.png

Result of positive flow succeeded.

image.png

Using the Deadband Value

  1. Open the Fieldbee navigation application.
  2. Go to Record Keeping> Vehicles.
  3. Find Calibrated tracktor and tap Edit.
  4. Tap the tractor angle field 8 times to open the Advanced Menu.




Deadband Calibration FAQ problems

New Page

FAQ – PowerWheel / Deadband Calibration Errors

image.png

❓ What does this error mean?

Error: Your deadband values are invalid. First value 20.0 and second value 14.0. Difference is more than 5 degrees.

This means the system detected that the difference between the two deadband limits is too large.
Normally, the difference must be ≤ 5°, but in this case it exceeds the allowed threshold.

❓ Why does this error happen?

Most common causes:

❓ Can this affect system performance?

Yes.

Incorrect deadband settings may cause:

FAQ – PowerWheel / Deadband Calibration Errors

❓ What does this error mean?

Error: Your deadband values are invalid. First value 20.0 and second value 14.0. Difference is more than 5 degrees.

This means the system detected that the difference between the two deadband limits is too large.
Normally, the difference must be ≤ 5°, but in this case it exceeds the allowed threshold.

❓ Why does this error happen?

Most common causes:

❓ Can this affect system performance?

Yes.

Incorrect deadband settings may cause:

FAQ – External Angle Sensor Not Found (PowerWheel)

What does this error mean?

“External Angle sensor not found!”

The system cannot detect the external steering angle sensor.
This means there is no valid signal coming from the sensor or firmware of the powerSteer controller  is not correct should be ..

What are the possible causes?

Most common reasons:



image.png