Skip to main content

MASSEY FERGUSON

MASSEY FERGUSON

66xx / 76xx / 77xx Series

Installation Overview

These instructions provide the suggested procedure for installing the FieldBee PowerSteer Ready autosteer system on qualified vehicles for the easiest installation and best performance. The vehicles covered by this manual are the Massey Ferguson vehicles with the factory-installed AutoGuide-2 steering system preparation. The AutoSteer installation kit PN: "FB_PowerSteer Ready KIT for Massey Ferguson (Series 66xx_76xx_77xx) " is used on the following vehicle series:

Supported Models:

Massey Ferguson 6612, 6613, 6614, 6615, 6616 (2014- AutoGuide2 MFWD)

Massey Ferguson 7614, 7615, 7616, 7618, 7619, 7620, 7622, 7624, 7626 (2013- AutoGuide2 MFWD)

Massey Ferguson 7714, 7715, 7716, 7718, 7719, 7720, 7722, 7724, 7726 (2015- AutoGuide2 MFWD)

Step Action Photo
1 Locate the cover on the right side of the seat between the seat and the side console on the floor.
2 Lift the locking latch and then remove the cover. CAN_connector_location.jpg
3 Locate the two CAN connectors inside the compartment. NOTE: The connectors can be located in different places inside the compartment depending on the machine model and when the machine was built. Use these figures as a guide to help locate and identify the correct ports. Locate the connector labelled X-184 and remove the plastic cover from the connector. SAM_5656.JPG
4 The connector will have a small white label that identifies it as X-184. This label may be on the bottom of the connector. The bracket holding the connectors can be removed by loosening the wing nut and removing the flat washer holding it to the frame to see the label if necessary. ALWAYS verify that the correct connector has been identified, as the Adapter Harness will physically connect to both ports, but only the X-184 connector will work.
5 Route the CAN Adapter Harness from the PowerSteer Ready main harness towards the vehicle CAN Connector. Attach the CAN Adapter Harness to the X-184 CAN connector on the vehicle. Note: Make sure the connector clicks to lock it into place. SAM_5692.JPG
6 Before the AutoSteer system can communicate to the AutoGuide2, the push buttons must be enabled. The buttons functions are as follows: Power AutoGuide2 System - This button powers up the GPS port on top of the cab and the rest of the AutoGuide2 system components. If this LED is not on, there will be no communications between the vehicle and the AutoSteer system. If the LED on this button is lit, the AutoGuide2 system is powered up and CAN messages will be communicated to the AutoSteer system; however, AutoSteering commands will be ignored until the Activate Steering button has been activated. Power_button_for_AutoGuide2_system.jpg
7 Activate Steering - This button enables or disables whether the AutoGuide2 system will accept steering commands from the AutoSteer system. If the LED on this button is not on, the AutoSteer system cannot send steering commands to the vehicle even though the AutoGuide2 and AutoSteer systems are powered up. If the LED on this button is lit, the AutoGuide2 system will accept steering commands from the AutoSteer system. Activating this button will automatically activate the Power AutoGuide2 System button LED. Enable_button_for_AutoGuide2_system.jpg
8 NOTE: Always put the AutoGuide2 Activate Steering button into OFF Position when driving on public roads.

MASSEY FERGUSON

67xxS / 77xxS Series

Installation Overview

These instructions provide the suggested procedure for installing the FieldBee PowerSteer Ready autosteer system on qualified vehicles for the easiest installation and best performance. The vehicles covered by this manual are the Massey Ferguson vehicles with the factory-installed MF-AutoGuide ready steering system preparation. The AutoSteer installation kit PN: "FB_PowerSteer Ready KIT for Massey Ferguson (Series 67xx_S - 77xx_S) " is used on the following vehicle series:

Supported Models:

Massey Ferguson 6713_S, 6714_S, 6715_S, 6716_S, 6718_S (2019-2021 MF AutoGuide Ready)

Massey Ferguson 7715_S, 7716_S, 7718_S, 7719_S (2019-2021 MF AutoGuide Ready)

Step Action Photo
1 Locate the buddy seat on the left side of the driver seat and remove the backrest. CAN_connector_location 67xxS.jpg
2 Locate the X594A Deutsch 12 pin (DT06-12S) Gateaway connector behind the backrest. Depending on the tractor's specification this connector can be either loose or connected to the Gateway unit. If it is connected, disconnect the connector from the Gateaway unit. IMG_5331.JPG
3 Depin using tool 1-1579007-2. Insert PWS.0170.MF.05 pins:
• Pin 6 → CAN-H (yellow)
• Pin 7 → CAN-L (green) Use contacts 2-968857-3. CPA must click.
4 Route cable through roof grommet. DO NOT reinstall large backshell – no space.
5 Connect to Main Harness CAN port. –
6 Activation: Datatronic 5 → Guidance Settings → External Control → On OR AGCO dealer uses EDT to set Auto-Guide flag + calibrate steering valve & WAS.

Critical checks

  • X972 CPA clicked
  • Dealer EDT activation
  • Firmware ≥ 2.6.1
  • Toolbox ≥ 6.14.5

8S/7S/6S Series (2020+) – Datatronic 5

(MF 8S.2xx - X972 connector)

Step Action Photo
1 Open fuse box cover in cab roof (right-hand side).
2 Locate purple 15-pin X972 (same as 5S).
3 Use PWS.0170.MF.06 – identical pinout (Pin 6 CAN-H, Pin 7 CAN-L). MF 8S insert
4 Activation identical to 5S series. –

Common for ALL Massey Ferguson Steer-Ready models

  • Controller firmware ≥ 2.6.1
  • FieldBee app ≥ 10.8 (or dedicated Steer Ready app)
  • Toolbox → Actuator type = Steer Ready
  • Kickout test MUST disengage instantly

Still no CAN? Send photo of connector + serial number → support@fieldbee.com (reply <1 hour).