Skip to main content

EN- FieldBee Navigation Application User Manual

Table of Contents

1. Introduction

Welcome to the FieldBee Android application User Guide. This manual describes how to install, set up, and use the application.

1.1. Technical assistance

If you have a problem and cannot find the information you need in the product documentation, contact our support team by writing to support@fieldbe.com.

1.2.Your comments

Your feedback about the documentation helps us to improve it with each revision. Please email your comments to
info@fieldbee.com.

1.3. General Warnings

Sign Safety Instruction
Always read the full documentation before installing or operating the PowerSteer system. Failure to follow safety precautions may lead to injury or damage.
NEVER leave the operator's seat with the system engaged. This prevents accidental death or injury from the vehicle running over someone. A person must always be present in the operator's seat.
Verify the area is CLEAR of people and obstacles before startup, calibration, tuning, or use of the system.
DO NOT operate on public roads or in public areas; power down the system while driving on them. Powering up the system on public roads can cause accidental engagement and loss of vehicle control.
The operator is responsible for safe driving at all time.
The system does not detect obstacles.
The system does not control vehicle speed; the operator must manually adjust speed to maintain control.

1.4. Installation Safety and Environment

Sign Installation & Safety Guidelines
DISCONNECT power (power OFF) before installing, removing, or performing maintenance on any connected components.
Ensure components are installed firmly. Improper installation may cause machine damage and poor performance.
Use a ladder to access vehicles Roof Safety when Insatlling the steering controllerto prevent falls
Avoid extreme environments: Do not install in environments with high temperature, heavy dust, harmful gases, flammables, explosives, great vibration, or strong noise.
Protect against water: Do not install the equipment in places vulnerable to water accumulation, seepage, dripping, or condensation, as this could damage the ports.<
Keep away from interference: Stay away from high-power wireless equipment, such as radar stations, transmitting stations, and substations, to avoid electromagnetic interference.
Do not frequently disassemble the equipment after installation to avoid accidental damage.

1.5. Electrical and Mechanical Safety

Sign Electrical & Installation Safety Guidelines
Electrical operations must be performed by qualified personnel.
CRITICAL PRE-CHECK: Verify all screws, bolts, nuts, and cable connections are tight before operation. Ensure all cables are secured to prevent damage.
Cable Routing (CRITICAL): DO NOT route cables over hot surfaces (e.g., engine block, exhaust) or near sharp/rotating parts (e.g., shafts, fan blades) to prevent melting, fire, tearing, or short circuits.
Unpredictable Movement Warning: Vehicle steering axles, tracks, or wheels may move unpredictably during testing or calibration. Ensure no people or obstacles are near the wheels during these stages.
Power Connection: Connect the negative terminal first, then the positive terminal.
Hydraulic Caution: Relieve hydraulic pressure before starting service if installation involves the hydraulic system.
Wear hand and eye protection during installation.
  • Mandatory Disengagement: It is critically important for the Manual Steering Override (Kickout) feature to be functioning and set to the proper level to allow the user to disengage AutoSteer manually. Never operate an AutoSteer system without this feature working or set properly.
  • Liability Disclaimer: Manufacturer disclaims any liability for damage or injury that results from failure to follow instructions, cautions, and warnings set forth herein, or as a result of operator actions that fall outside the recommended application.

2. Installation

image.png

The FieldBee app requires an Android OS version of at least 7.0.
Download the latest application from the Google Play Store:

info-alert.png
Warning! Before starting Registration or Login we recommend connecting to a stable internet connection!

3. Getting Started

App Startup screen.jpg

3.1. Language selection

Once the application is installed, you may choose your preferred language prior to commencing work.

The application is compatible with the following languages: English, Danish, Dutch, German, Hungarian, Latvian, Lithuanian, Mongolian, Polish, Portuguese, Russian, Spanish, Swedish, Turkish, Ukrainian, French, and Italian.

info-alert.png
Information If the device language is not supported by FieldBee Application, the application selects English by default.
Language Selection Screen
Language Selection.jpg
Fig.3.1 - Language Selection

3.2. End User Licence Aggrement

  • Prior to logging in, the application will request acceptance of the Fieldbee end user license agreement.
  • Click ACCEPT to successfully complete the login process.

Enduser Aggrement.jpg Fig.3.2 - End user Aggrement

3.3. Registration

Once the language selection & Aggrement is complete, you will proceed to the GET STARTED page (Fig.1.2). You have the following options:

  • Sign In using Google;
  • Sign Up with your email;
  • Sign In if you are already a registered user.
Getting Started Screen
Get Started Page.png
Fig.3.3 - Get Started Screen

3.3.1. Sign in with Google

  • Application will Ask you for Selecting the Required Account from Available list
  • Once Account Selected , Click SignIn to Begin Synchronization.

SignInusingGoogle.jpg Fig.3.4 - Sign in with Google

3.3.2. Sign up with Email

If you haven’t registered yet, tap "SIGN UP WITH EMAIL" to create an account using an email address:

info-alert.png
Information Read FieldBee end user license agreement carefully and ACCEPT to continue.

After accepting FieldBee end user license agreement, fill in the form, including:

  • Your Name;
  • E-mail;
  • Password
info-alert.png
Information! Password should be more than 4 and less than 32 symbols. Do not use special symbols as "%","$","+".

Create Email.jpg Fig.3.5 - Create EMIAL

  • Then tap "CREATE MY ACCOUNT".

Following your registration, a confirmation email containing your login credentials and password will be dispatched to the email address you provided. This information will be incorporated into your Profile.

3.3.3. Already Have account - SIGN IN

If User has Already an Account , by Clicking SIGN IN login can be Processed by providing below credentails

  • Email ID
  • Password

Already Has Account.jpg Fig.3.6 - Already Have Account - SIGN IN

  • After Providing click SIGN IN to begin Syncronization

3.4. Synchronization

info-alert.png
Information : If you are log in with your email, you need to use the Registration email for data Saving and Viewing in webportal .
  • After Suceessful Login , you will be directed to the synchronization screen to retrieve or initiate the synchronization of data.
info-alert.png
Please stay connected to the internet, it may take approximately 30 sec to 10 min depending on how much data you have stored in the app.

There are three types of data synchronization available, depending on customer preference:

  • Full Data Synchronization
  • Quick Synchronization
  • Custom Synchronization

For New User

Sign in. First synchronization.

Subsequently, the synchronization screen will be displayed. Kindly ensure that you remain connected to the internet, as this process may take anywhere from approximately 30 seconds to 10 minutes, depending on the amount of data you have saved in the application.

First synchronization refers to the initial exchange of data between the Android application and the server following installation or login. In this phase, the application retrieves the most recent settings, fields, tasks, routes, and other data updates from the server.

It guarantees that your configurations, fields, tasks, routes, and other data modifications remain consistent across all connected devices. This ensures that you consistently operate with the most up-to-date information and mitigates the risk of data loss.

info-alert.png
Synchronization means that your Android app and the server exchange data via internet to keep everything up to date.

User Data Types

User data is divided into two types:

Persistent Data Fields, crops, Navigation lines ,Vehicles, Implements , Notes , Materials
Operational Data Daily tasks , Recent tracks

After logging into the FieldBee app, the first synchronization will begin.

3.4.1. All data Synchronization

  • Syncs all persistent data and operational data from January 1st of the previous year up to the current date.
  • Example: If today is March 19, 2025, the app will sync data from January 1, 2024, to today.⚠ Due to Android device memory limitations, we cannot sync all user data at once.
info-alert.png
Information - Due to Android device memory limitations, we cannot sync all user data at once
Synchronize your Data Screen - All Data
Screenshot_20250319-130548.png

3.4.2. Quick Synchronization

  • Syncs all persistent data.
  • Syncs only operational data from the last month
Synchronize your Data Screen - Quick Sync
Screenshot_20250319-130553 (2).png

3.4.3. Custom Synchronization

  • Allows the user to select a custom start date for syncing operational data (from the selected date to today).
  • Syncs all persistent data.
  • Syncs operational data only from the selected date onward, up to one year before today.
Synchronize your Data Screen - Custom Sync Date Selection Apply Selected date
Screenshot_20250319-130615.png Screenshot_20250319-130712.png Screenshot_20250319-130721.png

This flexible synchronization process ensures that you get the necessary data while optimizing device storage and performance.

info-alert.png
Information - Quick Synchronization or Custom Synchronization is often useful when syncing data directly in the field.

Forgot which date was selected for synchronization

If you have used one of these synchronization options but forgot which date was selected:

  1. Open the FieldBee app.
  2. Go to Settings in the side menu.
  3. Tap Sync Now.

In this dialogue, you will observe the synchronization date (Basic Synchronization).

Syncronize date from Settings Menu
Screenshot_20250319-141901.png
Screenshot_20250319-142039.png
info-alert.png
Information - To change the synchronization date, you need to Sign out and log back in to the app.

This ensures that your data is correctly updated based on your needs. 🚜📡

  • Then Tap SYNC to Start Syncronize your data's.

Start Data Sync.png

Complete data sync.jpg

3.5. Password recovery

If you cannot recall your account password, please select "Forgot". Input the email address you used to register in the application, and then press "RESET".

info-alert.png
Information : If you haven't found the message, check the spam folder.
  • Navigate to New window to Send rest link to the required Email.
  • After Providing mail Id , Click Submit to Receive code to Provide New Password.
Click Forget Password Provide recovery Email
PaswordRecovery01.jpg Reset password.jpg

3.6. Getting Location

Upon completion of Data Synchronization, the Main Screen will become visible, and the Application will prompt you to grant access to your Location.

Getting Locataion.png Fig.3.10 - Getting Location

  • User can select the Required Option for getting location.

4. Application Menu structure

Navigation Application Menu Structure.

  • Navigation – Tractor guidance module that provides lightbar navigation, parallel lines, and connection to the external GPS sources and PowerSteer Controller.
  • Record keeping – management of the field activities such as tasks, fields, and crops.
  • My Equipment – management of the application’s paid modules.
  • Settings – control application parameters such as language, GPS settings, units of measurement and implement parameters.
  • Knowledge base – Contains user manuals and Support documents for Installation , Configuration , Troubleshootings.
  • Feedback – technical Support via Email /Whatsapp.
  • Premium- Management of the application’s paid modules.

Media (7).jpg

1. Navigation Screen 2. Record Keeping 3. MyEquipment
Navigation Screen.png Record Keeping Screen.jpg My Equipment Screen.jpg
4. Settings 5. Knowledge base 6. Feedback
Settings Screen.jpg Feedback Screen.jpg Feedback Screen.jpg
7. Premium
Premium Activation.jpg

What can be Configured

On Application Main Screen user can Configure

  • Tasks - ( Creating task , Selecting Vehicle & Implement , Guidancance line , Headland area , U- turn , Prescription map)
    • Settings of a track;
    • Record and save tracks;
    • Create a new Task or select from the created ones;
    • Create a new field or select from the created ones;
    • Create a new vehicle or select from the created ones;
    • Create a new Implement or select from the created ones;
    • Create a new Guideline or Select from the created ones;
    • View GPS accuracy and connect an external GPS source;
    • Adjust GPS settings;
    • Measure the area and perimeter using ruler modes;
    • Change map view and layer options;
    • Manual navigation with lightbar;
    • Automatic steering with Autosteer controller;
    • Headland working area Configuration;
    • U-Turn Configuration (Advanced &; Professional verison);
    • Prescription map Selection ( Professional version) -
  • Area - Ruler area
  • View - 2D/3D view , Precipstion map , Satellite Views
info-alert.png
Information : List of Icon used in Navigation Application during Configurations and field operations and respective Explanation
S.No
Image Explanation
1 List Icon.png The Main Menu button: Allows you to open and close the main menu from any app section.
2 GPS Fix Location.png Location: Centres the map to your current location
3 Ruler Image.png Ruler: Area and perimeter measurement.
4 Layer Image.png Layers: Allows to switch Map view modes (Normal, Hybrid, Satellite, Crop, Notes) and 2D/3D map view mode.
5 RTK signal.png Positioning accuracy: Information about current positioning accuracy Green - the accuracy is good for navigation Yellow - the accuracy is average Red - navigation is unavailable With this button you can: Connect device: Connect to an external GPS source Get better accuracy: You can go to the TAFE website to view the products to improve navigation quality.
6 Add Button.png New track: The button that allows you to Create the new track with appropriate settings: Task, Field, Vehicle, GPS accuracy and Pattern
7 Select task.png Select task: Create task with specified operation type, on several fields
8 Select Field.png Select field: You can measure the boundaries of your field
9 select-vehicle.png Select vehicle: You can select the vehicle and implement from the list or create one with specified parameters
10 pattern.png Pattern: Navigation patterns
11 arrow-head.png Start recording a track: The button starts the driving mode or your track recording.
12 implement-onoff-image.png Implement: You can turn your implement On or Off while recording a track
13 pause-button.png Pause: The button pauses recording a track. You can Continue or Save the track.
14 save-image.png Save: Save the recorded track
15 shift-line-image.png Shift lines: You can shift guidance lines relative to its initial position on paused track
16 delete-image.png Delete: Your track can be deleted with this button
17 additional-image.png The additional menu: This menu opens GPS setting (Navigation tolerance, GPS frequency, GPS quality filter) Sound and voice alerts settings Low-speed drive mode.
18 prescription-map-image.png Prescription Map menu: This Menu Provides to use Prescription based Autosteering system for Precise farming using farm management Datas (Only for Professional version)
Views Areas
Views.png Areas.png

5. AutoSteering Connection

For precision agriculture, we suggest the utilization of GNSS receivers. GNSS technology facilitates precision farming techniques, including precision planting, irrigation, and harvesting. It provides accurate positioning and control of agricultural machinery and equipment, leading to more efficient and precise operations.

Through the My Equipment wizard, we offer the ability to connect and set up different kinds of GNSS receivers and autosteers.

My Equipment Selection Screen for Configuration.jpg

To connect the PowerSteer system with the App, you need:

  • Set up the controller on the vehicle.
  • Turn On the device, wait until it becomes ready for connection.
    (For FieldBee controllers: the button on the controller will blink with green color.)
  • Then go to the FieldBee App, Main menu > My Equipment.
  • Select ADD EQUIPMENT for New Configuration.

Add Equipment Selection.PNG

5.1. Different Types were available To Establish Connection

Choose the device you want to Configure and connect from the list:

PowerSteer PowerGuide PowerSteer Dual
Power Steer Selection.jpg Power Guide Selection.jpg Power Steer Dual Connection.jpg
Power Steer Ready L1 Receiver Other GNSS Receivers
Power Steer Ready Connection.jpg L1 Reciver Connection.jpg Other Device Connection.jpg

5.2. PowerSteer Connection

After selecting the device, please adhere to the on-screen prompts to finalize the connection. You may verify the connection status of your devices in My Equipment. This encompasses the network, device connection, internet, and NTRIP connection.

  1. In the FieldBee App, go to My Equipment and tap Add Equipment (+).
  2. Select PowerSteer and tap Continue.

Power Steer Selection.jpg

A question appears: "Do you have your own FieldBee Base Station?" Do you own Base Station.jpg

  • If you answer "YES," we recommend configuring a base station before connecting the receiver.
  • If you answer "NO," it means you intend to connect to an NTRIP provider.

Next, a CONNECTION DIAGRAM will be displayed, outlining the connection process:

info-alert.png
Information! The connection diagram may vary depending on the device being connected.

Power Steer Connection Diagram.png

  • Turn ON the receiver.
  • Connect your hardware according to the displayed connection diagram.

Tap LET’S GO.

5.2.1. Network

Choose the network for connecting the FieldBee App and the receiver, then click CONTINUE.

Netwrok Setup template.jpg

info-alert.png
Information! We suggest configuring the network name as rtkwifi and using 12345678 as the password. PowerSteer will attempt to connect to the network using these default settings..

There will be three options for Selecting network type:

Network from this device (HotSpot) Network from another Android device (Wi-Fi) Network from router (Wi-Fi)
Netwrok from this device.jpg
Network from another device.jpg
Internal Network.jpg
If you've configured a SIM card with mobile internet, share the internet via a HotSpot. Connect to an available Wi-Fi network from another device. Connect to an available Wi-Fi network shared from a router using your current Phone/Tablet.
  • After selecting an Internet source, the Fieldbee App will test your internet connection and show confirmation if the internet connection was set up successfully.

Network connection successful.png

  • Tap CONNECT POWERSTEER CONTROLLER For Next Step

5.2.2. AutoSteer Controller - Search and Establish a Connection

Upon choosing the network, the application begins a search for accessible receivers. Consequently, it effectively detects the receiver.

  • The app initiates the connection process with the chosen Receiver / PowerSteer Controller.

Available Reciever.png

  • Once the device is Listed , Select and Tap CONTINUE to proceed Next Step.

Media (66).jpg

  • Upon connection is established successfully, Tap CONTINUE to proceed Next Step.
info-alert.png
Information! If you have multiple controllers linked to the same network, choose the one you wish to utilise.
info-alert.png
Information! If the app doesn't detect anything, simply tap REFRESH LIST.

For general information about connecting receivers and autosteer controllers, please refer to the Connecting to the receiver and autosteer basics section.

info-alert.png
Information! Further in this section, only the connection steps specific to the PowerSteer autosteer system are described.

5.2.3. PowerWheel. Check the connection

Next Step is to establish connection with the PowerWheel using a harness.

  • Press CONNECT TO POWER WHEEL to initiate the connection verification process.
  • The PowerWheel connection has been established successfully.

Power Wheel Connection.png

  • Now, tap CONNECT TO RTK to proceed and configure the NTRIP/Base Station connection.

5.2.4. RTK Setup

Next Step is to setup RTK Correction Source.

In order to set up corrections, it is necessary to connect with either a local NTRIP provider or establish a connection with a Fieldbee Base Station NTRIP or utilize Radio Mode. (Choose the Required Option - One Only)

info-alert.png
Information : By default, Fieldbee controllers connect to the Base Station(42C20000).
info-alert.png
Information : User will have three Option to Set for Correction Source.(Any One Should be Selected during Configuration)

To Connect to RTK: Tap ADD NTRIP PROVIDER. Then Select one of the NTRIP Sources:

  • Option - 1 : Local NTRIP provider.
  • Option - 2 : Latitude BASE Station NTRIP.
  • Option - 3 : Base Station in Radio Mode.
Local NTRIP provider Fieldbee BASE Station NTRIP Base Station in Radio Mode
Local NTRIP Provider.jpg Fieldbee Base station NTRIP.jpg Base Station in RADIO.jpg
Fig.5.14 Fig.5.15 Fig.5.16
5.2.4.1. NTRIP Mode

To Configure Fieldbee BASE Station NTRIP Mode.

  • Tap on ADD CORRECTION SOURCE
info-alert.png
Information : If Seperate Base Station Available with NTRIP Correction Sources

Add Correction Source.PNG Fig.5.17 - Correction Source Setup Screen

  • Select Fieldbee BASE Station NTRIP and Click Continue

Fieldbee Base station NTRIP.jpg Fig.5.18 - Correction Source - Fieldbee BASE Station NTRIP

  • Provide Base Station ID and Tap Continue

Base Station ID.jpg Fig.5.19 - Base Station ID

  • After completion, the application will verify the live status of the base station.
  • Once a connection is established, the controller will commence the rebooting process

Base Station live Status Check.jpg Fig.5.20 - Base Station Status Check

  • Following this, a Success! indication will be visible.
  • Finally, click Close.

NTRIP Connection Success Status.jpg Fig.5.21 - Base Status Successfull Connection status

  • Connected Base Station Status will be Visbiled

NTRIP Successfull Connection.jpg

Fig.5.22 - Base Station Details

5.2.4.2. Radio Mode
info-alert.png
Information : If Seperate Base Station Available with Radio Correction Sources

To Configure Fieldbee RADIO Mode.

  • Tap on ADD CORRECTION SOURCE

Add Correction Source.PNG

info-alert.png
Information : If Seperate Base Station Available with RADIO Correction Sources

Upon Selecting Fieldbee BASE Station NTRIP Mode

Base Station in RADIO.jpg Fig.5.24 - Correction Source - Base station in Radio mdoe

  • Tap Continue
  • The application will request confirmation for the installation of the radio antenna.

Radio Antenna Installation Indication Screen.jpg Fig.5.25 - Base Station ID

  • After verification, please tap CONSENT AND CONTINUE.
  • Once completed, the application will verify the live status of the base station.
  • After establishing a connection, the controller will initiate a reboot..

Base Station in Radio Mode.jpg Fig.5.26 - Base Station Status Check

  • Following this, a Success! indication will be visible.
  • Finally, click Close.
  • Connected Base Station Status will be Visbiled

NTRIP Successfull Connection.jpg Fig.5.28 - Base Station deatils

5.2.4.3. Local NTRIP Provider

To Configure Fieldbee Correction Service using Local NTRIP Provider.

  • Tap on ADD CORRECTION SOURCE

Add Correction Source.PNG

info-alert.png
Information : If Seperate Base Station Available with RADIO Correction Sources

Upon Selecting Local NTRIP Provider Mode

  • Tap Continue

Local NTRIP Provider.jpg Fig.5.30 - Local NTRIP Provider selection

  • Select Country and Required Credentails

Local NTRIP Country Selection.jpg Fig.5.31 - NTRIP Credentails

Local NTRIP County Details.jpg

  • Click Continue
  • After that , Connected Base Station Status will be Visbiled

NTRIP Successfull Connection.jpg Fig.5.32 - Base Station Details

5.2.5. Successful Configuration of System

  • In the Connection Successful activity, you have the opportunity to examine the connection diagram and verify that all statuses are linked on the left side.

Successfull Powersteer Configuration.png

The next step is to select or create a vehicle and enter the PowerSteer parameter.

  • Safety Note
info-alert.png
Warning! Do not use guidance systems on the roads. Always turn off the guidance system before entering the roadway.
info-alert.png
Warning! Do not attempt to enable (activate) the guidance system during transportation on the roadway.
info-alert.png
Warning! Guidance systems are designed to assist the operator in performing field operations more efficiently.
info-alert.png
Warning! The operator is always responsible for the path of the vehicle.
info-alert.png
Warning! Systems do not automatically detect or prevent collisions with obstacles or other vehicles.

5.3. Steer ready Connection

After selecting the device, please adhere to the on-screen prompts to finalize the connection. You may verify the connection status of your devices in My Equipment. This encompasses the network, device connection, internet, and NTRIP connection.

  1. In the FieldBee App, go to My Equipment and tap Add Equipment (+).
  2. Select PowerSteerReady and tap Continue.

Power Steer Ready Connection.jpg

A question appears: "Do you have your own FieldBee Base Station?" Do you own Base Station.jpg

  • If you answer "YES," we recommend configuring a base station before connecting the receiver.
  • If you answer "NO," it means you intend to connect to an NTRIP provider.

Next, a CONNECTION DIAGRAM will be displayed, outlining the connection process:

Screenshot_20250916-094041.png

  • Turn ON the receiver.
  • Connect your hardware according to the displayed connection diagram.

Tap LET’S GO.

5.3.1. Internet Connection

Choose the network for connecting the FieldBee App and the receiver, then click CONTINUE.

Netwrok Setup template.jpg

info-alert.png
Information! We suggest configuring the network name as rtkwifi and using 12345678 as the password. PowerSteer will attempt to connect to the network using these default settings..

There will be three options for Selecting network type:

Network from this device (HotSpot) Network from another Android device (Wi-Fi) Network from router (Wi-Fi)
Netwrok from this device.jpg
Network from another device.jpg
Internal Network.jpg
If you've configured a SIM card with mobile internet, share the internet via a HotSpot. Connect to an available Wi-Fi network from another device. Connect to an available Wi-Fi network shared from a router using your current Phone/Tablet.
  • After selecting an Internet source, the Fieldbee App will test your internet connection and show confirmation if the internet connection was set up successfully.

Network connection successful.png

  • Ensure your mobile device (tablet/phone with the FieldBee App) is connected to the Internet.
  • The Internet connection is required to receive correction data (NTRIP).

5.3.2. SteerReady Controller - Search and Establish a Connection

Upon choosing the network, the application begins a search for accessible receivers. Consequently, it effectively detects the receiver.

  • The app initiates the connection process with the chosen Receiver / SteerReady Controller.

Media (67).jpg

  • Once the device is Listed , Select and Tap CONTINUE to proceed Next Step.

Media (66).jpg

  • The FieldBee App communicates wirelessly with the PowerSteer Controller.
  • Make sure Wi-Fi is enabled on your mobile device. How find the Controller in network and connect to it.
info-alert.png
Information! If you have multiple controllers linked to the same network, choose the one you wish to utilise.
info-alert.png
Information! If the app doesn't detect anything, simply tap REFRESH LIST.

5.3.3.RTK Setup

Next Step is to setup RTK Correction Source.

In order to set up corrections, it is necessary to connect with either a local NTRIP provider or establish a connection with a Fieldbee Base Station NTRIP or utilize Radio Mode. (Choose the Required Option - One Only)

info-alert.png
Information : By default, Fieldbee controllers connect to the Base Station(42C20000).
info-alert.png
Information : User will have three Option to Set for Correction Source.(Any One Should be Selected during Configuration)

To Connect to RTK: Tap ADD NTRIP PROVIDER. Then Select one of the NTRIP Sources:

  • Option - 1 : Local NTRIP provider.
  • Option - 2 : Latitude BASE Station NTRIP.
  • Option - 3 : Base Station in Radio Mode.
Local NTRIP provider Fieldbee BASE Station NTRIP Base Station in Radio Mode
Local NTRIP Provider.jpg Fieldbee Base station NTRIP.jpg Base Station in RADIO.jpg
Fig.5.14 Fig.5.15 Fig.5.16
5.3.3.1. NTRIP Mode

To Configure Fieldbee BASE Station NTRIP Mode.

  • Tap on ADD CORRECTION SOURCE
info-alert.png
Information : If Seperate Base Station Available with NTRIP Correction Sources

Add Correction Source.PNG Fig.5.17 - Correction Source Setup Screen

  • Select Fieldbee BASE Station NTRIP and Click Continue

Fieldbee Base station NTRIP.jpg Fig.5.18 - Correction Source - Fieldbee BASE Station NTRIP

  • Provide Base Station ID and Tap Continue

Base Station ID.jpg Fig.5.19 - Base Station ID

  • After completion, the application will verify the live status of the base station.
  • Once a connection is established, the controller will commence the rebooting process

Base Station live Status Check.jpg Fig.5.20 - Base Station Status Check

  • Following this, a Success! indication will be visible.
  • Finally, click Close.

NTRIP Connection Success Status.jpg Fig.5.21 - Base Status Successfull Connection status

  • Connected Base Station Status will be Visbiled

NTRIP Successfull Connection.jpg

Fig.5.22 - Base Station Details

5.3.3.2. Radio Mode
info-alert.png
Information : If Seperate Base Station Available with Radio Correction Sources

To Configure Fieldbee RADIO Mode.

  • Tap on ADD CORRECTION SOURCE

Add Correction Source.PNG

info-alert.png
Information : If Seperate Base Station Available with RADIO Correction Sources

Upon Selecting Fieldbee BASE Station NTRIP Mode

Base Station in RADIO.jpg Fig.5.24 - Correction Source - Base station in Radio mdoe

  • Tap Continue
  • The application will request confirmation for the installation of the radio antenna.

Radio Antenna Installation Indication Screen.jpg Fig.5.25 - Base Station ID

  • After verification, please tap CONSENT AND CONTINUE.
  • Once completed, the application will verify the live status of the base station.
  • After establishing a connection, the controller will initiate a reboot..

Base Station in Radio Mode.jpg Fig.5.26 - Base Station Status Check

  • Following this, a Success! indication will be visible.
  • Finally, click Close.
  • Connected Base Station Status will be Visbiled

NTRIP Successfull Connection.jpg Fig.5.28 - Base Station deatils

5.3.3.3. Local NTRIP Provider

To Configure Fieldbee Correction Service using Local NTRIP Provider.

  • Tap on ADD CORRECTION SOURCE

Add Correction Source.PNG

info-alert.png
Information : If Seperate Base Station Available with RADIO Correction Sources

Upon Selecting Local NTRIP Provider Mode

  • Tap Continue

Local NTRIP Provider.jpg Fig.5.30 - Local NTRIP Provider selection

  • Select Country and Required Credentails

Local NTRIP Country Selection.jpg Fig.5.31 - NTRIP Credentails

Local NTRIP County Details.jpg

  • Click Continue
  • After that , Connected Base Station Status will be Visbiled

NTRIP Successfull Connection.jpg Fig.5.32 - Base Station Details

5.3.4.Controller to SteerReady Tractor

Final Step is to Connect the Controller with SteerReady Equiped Tractor

The PowerSteer Controller connects to the SteerReady tractor via the CAN interface.

This connection enables automatic steering functionality.

  • To create a new one, click ADD VEHICLE +

image.png

  • Next, input the Brand and Model of the SteerReady tractor, and Tap Continue.
  • Provide Required parameters for creating the Profile of Controller.
info-alert.png
Information : Refer to the How to create a vehicle and profile for more information.
info-alert.png
Information : If your Brand or Model is not listed, please contact support.
  • Select the SteerReady vehicle and SteerReady profile and tap Continue

image.png

  • Set CAN communication Setup by Tapping CONTINUE

image.png

  • Upon Successfull Connection , Tap Continue.

5.3.5. Successful Configuration of System

All connection steps have been completed. In the Connection Successful activity, you may examine the connection diagram and verify that all statuses are linked on the left side.

.image.png

5.4. Powersteer Dual Connection

After selecting the device, please adhere to the on-screen prompts to finalize the connection. You may verify the connection status of your devices in My Equipment. This encompasses the network, device connection, internet, and NTRIP connection.

  1. In the FieldBee App, go to My Equipment and tap Add Equipment (+).
  2. Select PowerSteerDual and tap Continue.

Power Steer Dual Connection.jpg

A question appears: "Do you have your own FieldBee Base Station?" Do you own Base Station.jpg

  • If you answer "YES," we recommend configuring a base station before connecting the receiver.
  • If you answer "NO," it means you intend to connect to an NTRIP provider.

Next, a CONNECTION DIAGRAM will be displayed, outlining the connection process:

info-alert.png
Information! The connection diagram may vary depending on the device being connected.

Power Steer Dual Connection Procedures.jpg

  • Turn ON the receiver.
  • Connect your hardware according to the displayed connection diagram.

Tap LET’S GO.

5.4.1. Network

Choose the network for connecting the FieldBee App and the receiver, then click CONTINUE.

Netwrok Setup template.jpg

info-alert.png
Information! We suggest configuring the network name as rtkwifi and using 12345678 as the password. PowerSteer will attempt to connect to the network using these default settings..

There will be three options for Selecting network type:

Network from this device (HotSpot) Network from another Android device (Wi-Fi) Network from router (Wi-Fi)
Netwrok from this device.jpg
Network from another device.jpg
Internal Network.jpg
If you've configured a SIM card with mobile internet, share the internet via a HotSpot. Connect to an available Wi-Fi network from another device. Connect to an available Wi-Fi network shared from a router using your current Phone/Tablet.
  • After selecting an Internet source, the Fieldbee App will test your internet connection and show confirmation if the internet connection was set up successfully.

Power Steer Dual Internet Connection.jpg

  • Tap CONNECT POWERSTEER CONTROLLER For Next Step

5.4.2. AutoSteer Controller - Search and Establish a Connection

Upon choosing the network, the application begins a search for accessible receivers. Consequently, it effectively detects the receiver.

  • The app initiates the connection process with the chosen Receiver / PowerSteer Controller.

Power Steer Dual Receivers.PNG

  • Once the device is Listed , Select and Tap CONTINUE to proceed Next Step.

Power Steer Dual Receivers Connected.PNG

  • Upon connection is established successfully, Tap CONTINUE to proceed Next Step.
info-alert.png
Information! If you have multiple controllers linked to the same network, choose the one you wish to utilise.
info-alert.png
Information! If the app doesn't detect anything, simply tap REFRESH LIST.

For general information about connecting receivers and autosteer controllers, please refer to the Connecting to the receiver and autosteer basics section.

info-alert.png
Information! Further in this section, only the connection steps specific to the PowerSteerDual autosteer system are described.

5.4.3. PowerWheel. Check the connection

Next Step is to establish connection with the PowerWheel using a harness.

  • Press CONNECT TO POWER WHEEL to initiate the connection verification process.
  • The PowerWheel connection has been established successfully.

Power steer Dual Motor Connections.PNG

  • Now, tap CONNECT TO RTK to proceed and configure the NTRIP/Base Station connection.

5.4.4. RTK Setup

Next Step is to setup RTK Correction Source.

In order to set up corrections, it is necessary to connect with either a local NTRIP provider or establish a connection with a Fieldbee Base Station NTRIP or utilize Radio Mode. (Choose the Required Option - One Only)

info-alert.png
Information : By default, Fieldbee controllers connect to the Base Station(42C20000).
info-alert.png
Information : User will have three Option to Set for Correction Source.(Any One Should be Selected during Configuration)

To Connect to RTK: Tap ADD NTRIP PROVIDER. Then Select one of the NTRIP Sources:

  • Option - 1 : Local NTRIP provider.
  • Option - 2 : Latitude BASE Station NTRIP.
  • Option - 3 : Base Station in Radio Mode.
Local NTRIP provider Fieldbee BASE Station NTRIP Base Station in Radio Mode
Local NTRIP Provider.jpg Fieldbee Base station NTRIP.jpg Base Station in RADIO.jpg
Fig.5.14 Fig.5.15 Fig.5.16
5.4.4.1. NTRIP Mode

To Configure Fieldbee BASE Station NTRIP Mode.

  • Tap on ADD CORRECTION SOURCE
info-alert.png
Information : If Seperate Base Station Available with NTRIP Correction Sources

Add Correction Source.PNG Fig.5.17 - Correction Source Setup Screen

  • Select Fieldbee BASE Station NTRIP and Click Continue

Fieldbee Base station NTRIP.jpg Fig.5.18 - Correction Source - Fieldbee BASE Station NTRIP

  • Provide Base Station ID and Tap Continue

Base Station ID.jpg Fig.5.19 - Base Station ID

  • After completion, the application will verify the live status of the base station.
  • Once a connection is established, the controller will commence the rebooting process

Base Station live Status Check.jpg Fig.5.20 - Base Station Status Check

  • Following this, a Success! indication will be visible.
  • Finally, click Close.

NTRIP Connection Success Status.jpg Fig.5.21 - Base Status Successfull Connection status

  • Connected Base Station Status will be Visbiled

NTRIP Successfull Connection.jpg

Fig.5.22 - Base Station Details

5.4.4.2. Radio Mode
info-alert.png
Information : If Seperate Base Station Available with Radio Correction Sources

To Configure Fieldbee RADIO Mode.

  • Tap on ADD CORRECTION SOURCE

Add Correction Source.PNG

info-alert.png
Information : If Seperate Base Station Available with RADIO Correction Sources

Upon Selecting Fieldbee BASE Station NTRIP Mode

Base Station in RADIO.jpg Fig.5.24 - Correction Source - Base station in Radio mdoe

  • Tap Continue
  • The application will request confirmation for the installation of the radio antenna.

Radio Antenna Installation Indication Screen.jpg Fig.5.25 - Base Station ID

  • After verification, please tap CONSENT AND CONTINUE.
  • Once completed, the application will verify the live status of the base station.
  • After establishing a connection, the controller will initiate a reboot..

Base Station in Radio Mode.jpg Fig.5.26 - Base Station Status Check

  • Following this, a Success! indication will be visible.
  • Finally, click Close.
  • Connected Base Station Status will be Visbiled

NTRIP Successfull Connection.jpg Fig.5.28 - Base Station deatils

5.4.4.3. Local NTRIP Provider

To Configure Fieldbee Correction Service using Local NTRIP Provider.

  • Tap on ADD CORRECTION SOURCE

Add Correction Source.PNG

info-alert.png
Information : If Seperate Base Station Available with RADIO Correction Sources

Upon Selecting Local NTRIP Provider Mode

  • Tap Continue

Local NTRIP Provider.jpg Fig.5.30 - Local NTRIP Provider selection

  • Select Country and Required Credentails

Local NTRIP Country Selection.jpg Fig.5.31 - NTRIP Credentails

Local NTRIP County Details.jpg

  • Click Continue
  • After that , Connected Base Station Status will be Visbiled

NTRIP Successfull Connection.jpg Fig.5.32 - Base Station Details

5.4.5. Successful Configuration of System

  • In the Connection Successful activity, you have the opportunity to examine the connection diagram and verify that all statuses are linked on the left side.

Successfull Powersteer Configuration.png

The next step is to select or create a vehicle and enter the PowerSteer parameter.

  • Safety Note
info-alert.png
Warning! Do not use guidance systems on the roads. Always turn off the guidance system before entering the roadway.
info-alert.png
Warning! Do not attempt to enable (activate) the guidance system during transportation on the roadway.
info-alert.png
Warning! Guidance systems are designed to assist the operator in performing field operations more efficiently.
info-alert.png
Warning! The operator is always responsible for the path of the vehicle.
info-alert.png
Warning! Systems do not automatically detect or prevent collisions with obstacles or other vehicles.

5.5. PowerGuide Connection

After selecting the device, please adhere to the on-screen prompts to finalize the connection. You may verify the connection status of your devices in My Equipment. This encompasses the network, device connection, internet, and NTRIP connection.

  1. In the FieldBee App, go to My Equipment and tap Add Equipment (+).
  2. Select PowerGudie and tap Continue.

Power Guide Selection.jpg

A question appears: "Do you have your own FieldBee Base Station?" Do you own Base Station.jpg

  • If you answer "YES," we recommend configuring a base station before connecting the receiver.

  • If you answer "NO," it means you intend to connect to an NTRIP provider.

  • Turn ON the receiver.

  • Connect your hardware according to the displayed connection diagram.

Tap LET’S GO.

For general information about connecting receivers and autosteer controllers, please refer to the
"Connecting to the receiver and autosteer basics" section.

info-alert.png
Information! Further in this section, only the connection steps specific to the PowerGuide autosteer system are described.

5.5.1. Network

Choose the network for connecting the FieldBee App and the receiver, then click CONTINUE.

PowerGuide Internet check.jpg

info-alert.png
Information! We suggest configuring the network name as rtkwifi and using 12345678 as the password. PowerSteer will attempt to connect to the network using these default settings..

There will be three options for Selecting network type:

Network from this device (HotSpot) Network from another Android device (Wi-Fi) Network from router (Wi-Fi)
Netwrok from this device.jpg
Network from another device.jpg
Internal Network.jpg
If you've configured a SIM card with mobile internet, share the internet via a HotSpot. Connect to an available Wi-Fi network from another device. Connect to an available Wi-Fi network shared from a router using your current Phone/Tablet.
  • After selecting an Internet source, the Fieldbee App will test your internet connection and show confirmation if the internet connection was set up successfully.

  • Ensure your mobile device (tablet/phone with the FieldBee App) is connected to the Internet.

  • The Internet connection is required to receive correction data (NTRIP).

Network connection successful.png

5.5.2. AutoSteer Controller - Search and Establish a Connection

Upon selecting the device type and network source, after successful network testing, the App initiates a scan for accessible PowerGuide controllers. As a result, it successfully identifies a PowerGuide Controller.

  • If you have multiple controllers linked to the same network, choose the one you wish to utilise.
  • If the App doesn't detect anything, simply tap REFRESH LIST.

Then, tap CONTINUE. The app initiates the connection process with the chosen PowerGuide Controller.

image.png

image.png

Once the connection is established successfully, CONNECT TO RTK.

5.5.3. RTK Setup

Next Step is to setup RTK Correction Source.

In order to set up corrections, it is necessary to connect with either a local NTRIP provider or establish a connection with a Fieldbee Base Station NTRIP or utilize Radio Mode. (Choose the Required Option - One Only)

info-alert.png
Information : By default, Fieldbee controllers connect to the Base Station(42C20000).
info-alert.png
Information : User will have three Option to Set for Correction Source.(Any One Should be Selected during Configuration)

To Connect to RTK: Tap ADD NTRIP PROVIDER. Then Select one of the NTRIP Sources:

  • Option - 1 : Local NTRIP provider.
  • Option - 2 : Latitude BASE Station NTRIP.
  • Option - 3 : Base Station in Radio Mode.
Local NTRIP provider Fieldbee BASE Station NTRIP Base Station in Radio Mode
Local NTRIP Provider.jpg Fieldbee Base station NTRIP.jpg Base Station in RADIO.jpg
Fig.5.14 Fig.5.15 Fig.5.16
5.5.3.1. NTRIP Mode

To Configure Fieldbee BASE Station NTRIP Mode.

  • Tap on ADD CORRECTION SOURCE
info-alert.png
Information : If Seperate Base Station Available with NTRIP Correction Sources

Add Correction Source.PNG Fig.5.17 - Correction Source Setup Screen

  • Select Fieldbee BASE Station NTRIP and Click Continue

Fieldbee Base station NTRIP.jpg Fig.5.18 - Correction Source - Fieldbee BASE Station NTRIP

  • Provide Base Station ID and Tap Continue

Base Station ID.jpg Fig.5.19 - Base Station ID

  • After completion, the application will verify the live status of the base station.
  • Once a connection is established, the controller will commence the rebooting process

Base Station live Status Check.jpg Fig.5.20 - Base Station Status Check

  • Following this, a Success! indication will be visible.
  • Finally, click Close.

NTRIP Connection Success Status.jpg Fig.5.21 - Base Status Successfull Connection status

  • Connected Base Station Status will be Visbiled

NTRIP Successfull Connection.jpg

Fig.5.22 - Base Station Details

5.5.3.2. Radio Mode
info-alert.png
Information : If Seperate Base Station Available with Radio Correction Sources

To Configure Fieldbee RADIO Mode.

  • Tap on ADD CORRECTION SOURCE

Add Correction Source.PNG

info-alert.png
Information : If Seperate Base Station Available with RADIO Correction Sources

Upon Selecting Fieldbee BASE Station NTRIP Mode

Base Station in RADIO.jpg Fig.5.24 - Correction Source - Base station in Radio mdoe

  • Tap Continue
  • The application will request confirmation for the installation of the radio antenna.

Radio Antenna Installation Indication Screen.jpg Fig.5.25 - Base Station ID

  • After verification, please tap CONSENT AND CONTINUE.
  • Once completed, the application will verify the live status of the base station.
  • After establishing a connection, the controller will initiate a reboot..

Base Station in Radio Mode.jpg Fig.5.26 - Base Station Status Check

  • Following this, a Success! indication will be visible.
  • Finally, click Close.
  • Connected Base Station Status will be Visbiled

NTRIP Successfull Connection.jpg Fig.5.28 - Base Station deatils

5.5.3.3. Local NTRIP Provider

To Configure Fieldbee Correction Service using Local NTRIP Provider.

  • Tap on ADD CORRECTION SOURCE

Add Correction Source.PNG

info-alert.png
Information : If Seperate Base Station Available with RADIO Correction Sources

Upon Selecting Local NTRIP Provider Mode

  • Tap Continue

Local NTRIP Provider.jpg Fig.5.30 - Local NTRIP Provider selection

  • Select Country and Required Credentails

Local NTRIP Country Selection.jpg Fig.5.31 - NTRIP Credentails

Local NTRIP County Details.jpg

  • Click Continue
  • After that , Connected Base Station Status will be Visbiled

NTRIP Successfull Connection.jpg Fig.5.32 - Base Station Details

5.5.4. Successful Configuration of System

  • In the Connection Successful activity, you have the opportunity to examine the connection diagram and verify that all statuses are linked on the left side.

Power Guide Successfull Configurations.jpg

  • Safety Note
info-alert.png
Warning! Do not use guidance systems on the roads. Always turn off the guidance system before entering the roadway.
info-alert.png
Warning! Do not attempt to enable (activate) the guidance system during transportation on the roadway.
info-alert.png
Warning! Guidance systems are designed to assist the operator in performing field operations more efficiently.
info-alert.png
Warning! The operator is always responsible for the path of the vehicle.
info-alert.png
Warning! Systems do not automatically detect or prevent collisions with obstacles or other vehicles.

6. Profile Setup

Upon finalizing the Autosteering Configuration, the subsequent step is to choose the Vehicle Profile.

There are two approaches to selecting the Vehicle Profile:

  1. Creating a New Vehicle
  2. Choosing from the Available Vehicle List

6.1. Create Vehicle

Configuring New Vehicle Profile

If you do not have any vehicles registered, please tap ADD VEHICLE +. In this process, the app will generate a vehicle along with a PowerSteer profile.

  • To Create New Vehicle, GO to My equipment & Add vehicle.

Add Vehicle.PNG

  • Choose the type of vehicle to be created.The available types are:
    • Tractor
    • Combined Harvester
Tractor Combined Harvester
Vehicle Selection - Tractor.jpg Harvester.jpg
  • After selecting the vehicle type, the user must provide the brand and vehicle models as outlined below:
    • Input the vehicle Brand and
    • Vehicle Model,
    • Optionally, you may enter a Name (the default vehicle name will be generated from the brand and model),
    • Year of manufacturing, and
    • Drive type (2WD or 4WD).

Vehcile Deatils.jpg Fig.6.3 - Vehicle naming Screen

  • Following the vehicle models, you are required to input the subsequent information regarding the vehicle dimensions:
    • Wheelbase
    • Rear axle
    • Wheel angle (max)
Wheel base Rear axle Turn angle
WheelBase.jpg Rear Axle.jpg Turn Angle.jpg
Fig.6.4 Fig.6.5 Fig.6.6
Distance beetween front wheel and back wheel centers Distance beetween rear axle tire centers Max turn Angle
info-alert.png
Information : You can refer to the vehicle operation manual or your local vehicle manufacturer dealer to get your factory front wheels maximum turn angle value.
  • At the final step of the wizard, a summary will be presented. Please review the summary information thoroughly and make any necessary adjustments to the measurements.

Vehicle Dimensions Summary.jpg Fig.6.7 - Created Profile View Sceen

  • If all measurements are accurate, please tap the "SAVE PROFILE" button to complete the implementation of creation and save.

Vehicle Created.jpg Fig.6.8 - Successful Profile Creation Screen

6.2. Create a Autosteer Profile for Vehicle

The subsequent step involves configuring the PowerSteer Controller profile for the corresponding vehicle by incorporating the required parameters.

  • If the PowerSteer profile already exists, it can be selected directly.

Powersteer Vehicle Profile.jpg

  • If it does not exist, a new profile must be created for respective Vehicle

Asking for Creating Power Steer Profile Creation.jpg

info-alert.png
Information : If you have saved a vehicle, you can use it & tap ADD POWERSTEER PROFILE +

6.2.1. Auosteer Controller Installing Location

For the creation of a Powersteer profile, two options will be available for the installation of the controller:

  • On the bonnet (hood);
  • On the roof.
On the bonnet (hood) On the roof
Bonnet.jpg Roof.jpg
Fig.6.4 Fig.6.5

6.2.2. Controller Height Position.

Then, you may access the Controller settings for Position Height:

Controller Height.jpg

  • Position Height: The height from the ground to the bottom of the controller. It should be between 1 cm and 600 cm.

6.2.3. Controller Offset Direction.

Then, you can enter the Controller settings for Left/Right Offset :

Controller Front Position.jpg

  • Left/Right Offset: The distance from the tractor's centerline to the controller. It should be between 0 cm and 300 cm.
Left Offset Right Offset
shared image (2).jpg shared image (5).jpg

6.2.4. Controller Front Offset.

Then, you may access the Controller settings for Front Offset :

  • Front Offset: The distance from the center of the rear axle to the center of the controller. It should be between 25 cm and 1000 cm.

Controller Front Installation.jpg

info-alert.png
Information : We recommend setting the controller at a minimum Front offset 80 cm.
  • Examine the Overview of Measurements. If needed, you may select a parameter, and the application will revert to the chosen parameter.

Power Steer Profile Summary.jpg

  • Named PowerSteer profile and set to controller.

PowerSteer Profile Name.jpg

  • Tap SAVE PROFILE to Complete the Profile Creation Process

Successfull powersteer Profile Creation.jpg

6.3. Installation Summary.

Description On the Bonnet Top of Vehicle
Reciver Installation Location Bonnet.jpg Roof.jpg
Receiver Front Offset Controller Front Position.jpg Controller front Offset - on the Hood.jpg
Receiver Height from Ground level Controller Height.jpg Controller Height - on the Hood.jpg
Receiver Distance from Rear axle Controller Front Installation.jpg Controller Front Installation - on the Hood.jpg

Next step Calibration Vehicle and PowerSteer profile.

7. Calibration

To ensure precise navigation with PowerSteer, you must calibrate your vehicle with the PowerSteer profile.

  • Tilt Calibration (required)

    • To ensures the accuracy of the steering system by compensating for any inclination of the controller due to uneven terrain. Without proper calibration, the system may misinterpret the vehicle’s orientation, leading to inaccurate steering adjustments.
  • Angle Calibration (required)

    • To ensures that the steering controller accurately interprets the wheel angle, preventing incorrect steering commands and improving overall navigation precision. Without proper calibration, the system may miscalculate turning angles, leading to steering inaccuracies.
  • Advanced angle Calibration (optional)

    • To achieve a more accurate Turn Angle Ratio for your vehicle, we recommend performing this calibration. It helps with:
      • Reducing long entry times when aligning with the guidance line.
      • Minimizing cross-track errors that cause drifting to one side.
      • Correcting steering column asymmetry for improved accuracy.

    This calibration enhances steering precision and overall system performance.

7.1. Tilt Calibration

Tilt calibration ensures accurate steering by compensating for any tilt in the controller. To perform the calibration, you will need approximately two minutes and a flat surface. Follow these steps:

  1. Mark the initial position of the wheels.
  2. Park the tractor on a flat surface and remain stationary for 15 seconds to allow the system to record the tilt data.
  3. Turn the tractor 180 degrees.
  4. Stop on the same flat surface and remain stationary for another 15 seconds to complete the calibration.

This process helps the system correct any tilt-related errors, improving steering accuracy on uneven terrain.

Step 1 Step 2
Tilt Calibration step 1.jpg Media (11).jpg
Stop and Mark the Wheel position Remain stationary for 15 seconds
Step 3 Step 4
Tilt Calibration step 3.jpg Tilt Calibration step 4.jpg
Turn Tractor to 180 Dgeree Remain stationary for another 15 seconds after turning Vehicle

7.2. Turn Angle calibration

Turn angle calibration ensures accurate steering response by correctly mapping the full range of wheel movement. The process takes approximately two minutes and requires a flat surface. Follow these steps:

  1. Park the tractor on a flat surface.
  2. Fully turn the steering wheel to the left and tap "OK" to confirm.
  3. Fully turn the steering wheel to the right and tap "OK" to complete the calibration.

This calibration allows the system to precisely detect steering angles, improving navigation accuracy and overall performance.

Park the Vehicle Turn Full Left
Turn Angle Step-1.jpg
Turn Angle Step-2.jpg
Turn Full Right Completed Calibration
Turn Angle Step-3.jpg Turn Angle Step-4.jpg

7.3. Advanced Turn Angle calibration

Advanced Turn Angle Calibration is available from firmware version 2.3.6.

For Advanced Turn Angle Calibration, both Tilt Calibration and Turn Angle Calibration must be completed first.

To perform this calibration, you will need 5 to 15 minutes and an open space (the required area is calculated based on the wheelbase). The recommended speed is 3–5 km/h.

During calibration, the system will automatically steer the tractor in a figure-eight pattern.

Advance Calibration Details.jpg

Do not switch to manual control.

Calibration Completion Criteria:

  • 3 successful right turns completed.
  • 3 successful left turns completed.

Advance Calibration in Progress.jpg

8. Basic Functional Verification

Basic functional verification can be conducted following the system configurations.

The configurations include:

  1. Power steer connection
  2. Vehicle selection
  3. Guidelines selection
  4. Engaging the autosteering system

1. Powersteer Connection Status

Before Configuration After configuration
My Equipment Screen.jpg After Connections.jpg

2. Vehicle Selection

  • After Configurtion and selecting vehicle( Completed Calibration)

Vehicle Selection - Calibrated.jpg

3. Guidelines Selection

After Selecting Vehicle , Click on AB pattern and Select the Required Guidelines

  • Click Start navigation to create AB pattern and Select AB Guidelines

Select Guidelines.jpg

  • Select AB Straight pattern and click Save to continue

AB Straight.jpg

  • After Selecting Guideline , Plot A and B to Create Guidelines
A - Point B - Point
A point.jpg B point.jpg
  • Click Engage Button , to Activate Autosteering.

Autosteering Engage.jpg

  • Following the engagement of the system, the steering mechanism will be automated.
  • Upon completion, the fundamental verification of autosteering is finalized, and the system is prepared for operation.
info-alert.png
Information : In Case of Error Indication , Please Verfy the Internet Connections , Physical Wiring Connection to Check the Status*

Steering Enable / Disable.

To control steering you can use the following controls on the Navigation screen while driving:

S.No Image Descriptions Explanation
1
Steering Engage.png
Engage
Autosteer Engage - This indicates that Autosteer is currently DISABLED. Press this button to ENABLE Autosteer. Once you press this button, Autosteer will begin to follow the guiding line and will drive forward automatically
2
Steering Disenage.png
Disengage
Autosteer Disengage - This indicates that Autosteer is currently ENABLED. Press this button to DISABLE Autosteer. Once this button is pressed, Autosteer will cease to follow the guiding line, requiring the driver to take control of the steering wheel. To deactivate Autosteer, simply turn the steering wheel. After turning the steering wheel, the driver must operate the vehicle manually.
3
Steering Error.png
Error Autosteer Error - This indicates that Autosteer is currently experiencing a Steering Interruption.
4
Settings Icon.png
Adjust
Steering Adjustment - The Steering Adjustment feature allows the operator to modify the vehicle's steering performance to accommodate varying conditions. The response of the chosen item can be altered by utilizing the slider bar.

9. Manual Override setting

Configuring the Manual Override feature to disengage the system based on the driver's intention during emergencies or necessary conditions,

Setup Manual Override

  • Go to MyEquipment > Manual Override

Manaul Override- Selection.jpg

Setting Value Click SET to Apply
Manaul Override- Set Value.jpg Manaul Override- Clik OK.jpg
info-alert.png
Information : User Can Set the Manual Override Value Range from 5(Sensitive) to 20(Strong) to take control of Steering wheel (Disengage Autosteer)

10. Field Operation Requirements

After Completing the Basic Functional verifications , user can start work on Field Operations.

To Perform field operation , User need to Provide the Necessasry informations to start the Task

Mandatory Informations :

TASK FIELD VEHICLE IMPLEMENT GUIDELINES
Select from the Available list (Fertilization , Spraying , Tilling , Planting , Harvesting , ....) Select the Required Field ( Created and Saved Previously) Select the Required vehicle ( Created and Saved Previously (Calibrated Vehicle)) Select the Required Implement Select the Required Pattern to be Driven
Task Selection.png Field Selection.png Vehicle Selection.jpg implement-selection.png guide-lines.png

Optional ( Based on requirment ):

U-TURN HEADLAND PRESCRIPTION MAP
Enable and Configure Enable and Configure Upload the Map file
U turn Enable.png work area.png
  • Then Proceed for Field Operation by Click Arrow Head

10.1. Safety Indication before Start

Before start of Field Operation , Navigation App will screen you the Safety Indications. After Reading the Notes , Click I Understand &; Accept to start the Process.

Safety Indiaction.jpg

11. Navigation patterns

Overview & Systems Safety

info-alert.png
Information : Do not use guidance systems on the roads. Always turn off the guidance system before entering the roadway.
info-alert.png
Information : Do not attempt to enable (activate) the guidance system during transportation on the roadway.
info-alert.png
Information : Guidance systems are designed to assist the operator in performing field operations more efficiently.
info-alert.png
Information : The operator is always responsible for the path of the vehicle..
info-alert.png
Information : Systems do not automatically detect or prevent collisions with obstacles or other vehicles.
Descriptions Images
Guidance Lines
All used patterns for the field with different implement width are available for the next Task. You can easily execute operations with different implements. Once you created guiding lines - they will be available for further works. guidelines.jpg
AB straight
AB straight is suitable for the regular shaped square or rectangular fields, without “non operational spots”. In this case, our system will automatically draw parallel straight lines that you should follow on your field. ab-straight.jpg
AB curve
АВ curve is suitable for all field’s shapes and particularly for fields with “non-operational spots”. In this case, you will make the first run along a curved/non-straight line, after the first turn the application will create next lines parallel to the first run. ab-curve.jpg
AB Manual
AB Manual is suitable for building straight guidelines on the field regardless of whether you are dri-ving or standing. You can set A and B points manually at any place on the field you want. And then parallel straight lines will be automatically drawn. ab-manual.jpg
Headland straight/Headland curve
Headland is suitable for spraying operations. In this case, you will make the first run along the borders of the field, set A and B points on one side, after driving around the field the application will calculate all lines for the field and calculate the remaining area. headland-straight.jpg
Multiple Headland
Multiple Headland pattern is suitable for operations with small implements like (planting, plowing, etc). When Multiple Headland pattern is selected, the user can set up the number of headlands that he wants to process around the field and also select the Internal pattern. While navigating, the user can switch between Headland and Internal patterns. multiple-headland.jpg
Saved track
With the “Saved track” pattern you can always return to the same line in the field. It is suitable to work in a field with a difficult symmetry. It enables you to use a previously saved track as the line for tractor guidance. saved-track.jpg

11.1. AB Patterns - Straight , Curve , Manual

  1. AB Straight - AB straight is suitable for regularly shaped square or rectangular fields without “non-operational spots”. In this case, our system will automatically draw parallel straight lines that you should follow on your field

  2. AB Curve - AB curve is suitable for all field shapes and particularly for fields with “non-operational spots”. In this case, you will make the first run along a curved/non-straight line. After the first turn, the application will create the next lines.

  3. AB Manual - AB Manual pattern allows you to create the first line Manually even before the tractor drives into the field. In this case, our system automatically draws parallel straight lines to the line you created initially

To Create Pattern

    Step-1 : Select Required Guideline Step-2 : Plot A point and B Point Step-3 : Activate Autosteering mode
    info-alert.png
    Information : For the AB Manual, display Plot A and Plot B on the screen. The tractor may remain in a static condition.
    AB Straight AB Curve AB Manual
    AB Straight Selection.jpg AB Curve Selection.jpg AB Manual Selection.jpg
    A point.jpg A point - AB Curve.jpg A point AB Manual.jpg
    B point.jpg B point AB Curve.jpg B point AB Manual.jpg
    Autosteering Engage.jpg AB Curve Engage.jpg AB Manual Engage.jpg

    11.2. Multiple Headland

    Headland is suitable for spraying operations. In this case, you will make the first run along the contour of the fieldset A and B points on one side. After driving around the field the application will calculate all lines for the field and will calculate the remaining area

    To Create Pattern

      Step-1 : Select Required Guideline Step-2 : Configure Headland type and area's Step-3 : Plot A point and B Point Step-4 ; Select Area to Operate ( Work/Headland) Step-5 : Activate Autosteering mode

      Muliple Headland.jpg Fig.10.11 - Selecting Multiple Headland

      Configuration

      • After Selecting , App will ask for type of headland pattern and headland area required to process.
      • Required Details
        1. Set Headland lines
        2. Build headland with rounded corner
        3. Internal pattern
      AB Straight AB Curve AB Manual
      Multiple Headland AB Straight.jpg Multiple Headland AB Curve.jpg Multiple Headland AB Manaul.jpg

      Fig.10.12 - Selecting Multiple Headland Patterns

      Execution

      1. Setting headland lines

      • Provide Number of Required headland areas
      Setting Headland lines = 4 Visbisle Guidelines after configuration
      Multiple Headland AB Straight.jpg Multiple Headland - working Headland area.jpg

      2. Setting Inernal patterns

      • Select Required patterns to be used and Plot A and B point to generate Guidelines
      AB Straight Visbisle Guidelines after configuration
      Multiple Headland AB Straight.jpg Multiple Headland - working Inside area.jpg
      AB Curve Visbisle Guidelines after configuration
      Setting Multiple Healand - Headland area.jpg Multiple Headland - working Inside area (AB curve).jpg

      Fig.10.13 - Creating A point

      Work area & Headland area

      • Select Required area to be operated by taping the Mentioned Icons
      Work area Headland area
      Multiple Headland - select work area working.PNG Multiple Headland - select headland area working.PNG

      11.3. Saved tracks , Guidelines

      1. Guidelines - All used patterns for the field with different implement widths are available for the next Task. You can easily execute operations with different implements. Once you created guiding lines – they will be available for further works

      2. Saved Tracks - Saved track” pattern, you can always return to the same line in the field. It is suitable to work in a field with a difficult symmetry. It enables you to use a previously saved track as the line for tractor guidance

      Guidelines

      • To Create Guideline using saved tracks
      • Go to Navigation Screen > Select Guidelines

      Guidelines seletion.jpg Fig.10.16 - Selecting Saved Track

      • After Selecting , list of Previuously used guidelines will be availabe.
      • Select the required patter to execute/Continue the operation.

      Available Guidelines.png Fig.10.17 - Saved Tracks

      Saved Track

      To set a straight AB line with an Guidance Lines, driving is not necessary.

      Start driving (Guidance Lines ):

      • To Create Guideline using Guidance Lines
      • Go to Navigation Screen > Select Saved tracks

      Saved tracks.jpg Fig.10.18 - Selecting Guidance Lines

      • After Selecting , list of Previuously Saved tracks will be availabe.
      • Select the required patter to execute/Continue the operation.

      List of saved tracks.png Fig.10.19 - Saved Guidance Lines

      12. Tuning Paramters

      Once the vehicle has undergone calibration, it is expected to function effectively for the majority of standard field operations.

      Nevertheless, in specific circumstances, modifications to the steering performance may be necessary, influenced by elements such as field conditions and the type of implement.

      Upon initiating navigation with PowerSteer, once the navigation lines are displayed on the map, the Steering button and the Gear button (Steering Adjust Parameters) will become visible.

      Autosteering Engage.jpg

      12.1. What parametes can be adjusted:

      1. Line Acquisition refers to a parameter for steering adjustment that dictates the speed and smoothness with which the vehicle aligns itself with the guidance line once autosteering is activated.
      2. Tilt Compensation is a parameter for steering adjustment that can be toggled on or off to rectify steering deviations resulting from uneven terrain.
      3. Motor Aggressiveness is a parameter for steering adjustment that regulates the intensity and speed at which the motor rotates the steering wheel.
      info-alert.png
      Information : Motor Aggressiveness will be Automatically adjusted in Position Mode.
      Position Mode Speed Mode (Outdated)
      Position Mode - Tuning.jpg Speed Mode - Tuning.jpg
      In Position mode Motor Aggressiveness will be automatically Adjusted In Speed Mode Motor Aggressiveness will be Manually Adjusted
      • To access the Steering Adjust dialog, tap the Gear button on the Navigation screen.

      12.1.1. PowerWheel: Position Mode

      From this point, you can configure:

      • Line acquisition.

      • Higher values – The vehicle aligns with the line more assertively, which decreases acquisition time but may lead to overshooting.

      • Lower values – The approach is more gradual and smooth, reducing sudden corrections but extending the time required for alignment.

      • Tilt compensation OFF/ON.

      • ON – The system adjusts for vehicle tilt, enhancing accuracy on slopes and uneven terrain.

      • OFF – No tilt adjustments are made, which could lead to minor deviations, particularly on irregular surfaces.

      • Motor aggressiveness. Adjusted automatically.

      12.1.2. PowerWheel: Speed Mode (Outdated)

      info-alert.png
      Information : Starting from firmware version 2.2.x, we recommend switching the motor to Position Mode. You can do this through the Toolbox app.**

      From this point, you can configure:

      • Line acquisition.
      • Tilt compensation
      • Motor aggressiveness.
        • Higher values – The motor responds more aggressively, making faster and sharper steering corrections. Useful for high-speed operations or when quick adjustments are needed.
        • Lower values – The motor turns the wheel more smoothly and gradually, reducing sudden movements. Ideal for slower speeds or delicate steering conditions.

      13. U-Turn Feature

      Once the guidance lines have been established, the user is able to configure U-turn patterns.

      • Setting up an automatic U-turn during field operations, it is necessary to enable the U-turn feature.

      To create a U-turn

      • Goto MyEquipment & Tap U-turn

      U turn Enable.png

      Fig.11.1 - Select U-Turn

      • After that , Enable U-turn Feature

      U turn Enabling.png

      • Necesseray Paramters for Configuring U-turn
        1. Provide Left/Right Turn Rquired
        2. Start from Line Number
        3. Skip lines
        4. Minimal turn radius (cm)
        5. Vehicle Speed during a turn(km/hr)

      U turn Configuration.png Fig.11.2 - U-Turn Configuration

      U turn Configuration updated .png

      • After Configuration , U-turn Feature can be utilized During Field Operation.

      14. Headland Creation

      Headland Creation allows users to establish the necessary headland area and select the specific area for work (Headland area/Work Area).

      To Configure Headland pattern

      • Go to Navigation Screen
      • Click Add > Select Work Area

      work area.png Fig.12.1 - Activating Wore Area

      14.1.Configuration

      While enabling the Headland pattern, the user has two options for configuring the Headland area.

      1. On Work Area
      • Guidance lines will not be available in the Headland area.
      • U-turns will be available in the Headland area.
      1. On Headland
      • Field operations will be executed in the Headland area.

      Configuration

      • Click on ADD HEADLAND

      On work area.jpg Fig.12.2 - Selecting On Work Area

      • After Slecting , Application will ask for type of Headland need to be utilized

      • There will be three Headland Patterns were Available

        1. Select Headland type ,
        2. Headland Width ,
        3. Provide Headland Name
      Ring Type Field Side Segement
      Ring type.jpg Field Side.jpg Segmeneted.jpg
      Pattern Create Headland Area on all Corner of the Field Pattern Create Headland Area on Specific Corner of the Field based on User Setting Pattern Create Headland Area on Specific Corner of the Field based on User Setting
      • After Headland Configuration , User can select the area need to be Operated first (Work area / Headland area)

      14.2. On Work Area

      • Work Zone, Encompasses Field Operations Within the Field While Taking into Account the Headland Area
      Work Area selection Field Operation Execution
      Selecting work area.jpg Working on Work area.jpg

      14.3. On Headland area

      Upon selecting the Headland area, guidelines will be plotted exclusively in the Headland region to facilitate the completion of field operations in Headland areas.

      Headland Area selection Field Operation Execution
      on Headland area.jpg on Headland area operation.jpg

      15. Record Keepings

      XRecorder_20260127_12.jpg

      15.1. Tasks

      15.1.1. Task View

      15.1.2. Creating New Task

      15.1.3. Search and Filter Tasks

      15.1.4. Short and delete Tasks

      15.2. Fields

      15.2.1. Fields List View

      15.2.2. New Field- Manual Creation

      15.2.3. New field - GPS Measurment

      15.2.4. Field card

      15.2.5. Add Headland

      15.2.6. Add Prescription Map

      15.2.7. Create AB line from Filed edge(Copy Side)

      15.3. Guidance lines

      15.3.1. Saved/Recently used Guidelines

      15.4. Notes

      15.4.1. Obstacles Locations

      15.5. Vehicles

      15.5.1. Creating New Vehicle Profile

      15.6. Implements

      15.6.1. Creating New Implement

      15.6.2. Creating Reversible Implement

      15.6.3. Creating Section control Implement

      15.6.4. Creating front Implement Setup

      15.7. Materials

      15.8. Crops

      15.9. Workers

      16. Application Settings

      Within the Application Settings, users have the ability to configure System Settings, Navigation Settings (Tolerance, Sound, Implement On/OFF, Reverse Movement, Operating Speed, Quick Start)

      16.1. System Settings

      In the System settings, the user has the ability to configure:

      • System language
      • Unit of Measurement
      • Synchronization

      Settings Screen.jpg Fig.14.1 - System Setting Screen

      Language Units Synchronization
      Language Selection - Settings.png Unit Measurement-settings.png Synchronization - settings.jpg
      Fig.14.2 Fig.14.3 Fig.14.4
      Select Prefered language Select Required Unit of Measurement Select Prefered Synchronization from data

      16.2. Navigation settings

      Navigation Settings enable users to adjust precision and automation features with greater accuracy.

      • Important options consist of Navigation tolerance, sound/voice alerts, and an option to automatically turn off implements when out of the field.
      • Further settings comprise reverse movement recognition (Beta),
      • a speed threshold for operations below 1 km/h, and
      • Quick Start Mode.
      • These settings contribute to improved precision and efficiency in navigation-related applications.

      Navigation settings screen.png Fig.14.5 - Navigation Setting Screen

      16.2.1. Sound and voice alerts.

      Audio and voice notifications enable you to choose which sound and voice alerts you wish to receive.

      Sound and Voice Alert.png Fig.14.7 - Sound/Voice Alert Setting Screen

      • Deviation (Red) - an audible alert will sound if there is a significant deviation from the designated line.
      • Accuracy - a voice notification will be provided when there is a change in the accuracy level.
      • Implement lifted - a voice notification will occur when the implement is lifted (the covered area will not be recorded).
      • Autosteer sounds - an audible alert will sound if an autosteer error has occurred.
      • Autosteer voice sounds - a voice notification will inform about the status of the autosteer.

      16.2.2. Deviation Type (avalible from v.10.6.6)

      • This parameter specifies the method employed to assess deviation from the designated path:

      • Distance (XTD - Cross Track Distance). (This is the Default option.) It measures the perpendicular distance from the current location to the intended route, indicating how far the system has deviated from the optimal path.

      • Direction (XTE - Cross Track Error) signifies the directional error or lateral displacement from the navigation line, commonly utilized for real-time course adjustments. Choosing the correct type of deviation is crucial for ensuring accurate navigation and optimal path-following efficiency.

      16.2.3. Disable Implementation When Outside the Field (Enabled by Default)

      This functionality automatically disables the implement and halts the computation of the covered area when the system identifies that it has moved beyond the field limits..

      Once the implement returns to the field boundaries, it is automatically reactivated.

      Implement ONOFF Settings.PNG Fig.14.8 - Turn Implement OFF when Outside Field

      Manual Implement ON/OFF Status

      • To Control Implement Status manually , User can Click the Implement Icon to Turn OFF

      Implement OFF Indication.PNG Fig.14.9 - Implement OFF

      • To Control Implement Status manually , User can Click the Implement Icon to Turn ON

      Implement ON Indication.PNG Fig.14.10 - Implement ON

      16.2.4. Reverse movement recognition (Beta)

      This option allows for the activation and deactivation of the recognition feature when the vehicle is in reverse. If reverse movement is detected, the vehicle's arrow color will change to blue, and the coverage area will automatically cease recording.

      • Enhances the stability of headings, thereby preventing abrupt changes in the application that may occur due to alterations in movement direction.
      • The default setting for reverse movement recognition is OFF.

      Reverse Direction settings.png Fig.14.11 - Reverse Movement Recognition ON/OFF

      • Once Reverse Movement is Activated, an indication will be visible at the bottom left of the screen when the vehicle is traveling in the reverse direction.

      Reverse Movement Detection.PNG

      Fig.14.12 - Reverse Movement Indication

      16.2.5. Ultra Slow Speed Mode

      This option enables low speed mode, which allows for the activation of autosteer at speeds below 1 km/h and enhances heading calculation during slow speed operations.

      • By default, speeds below 1 km/h are set to OFF.

      16.2.6. Quick start mode.

      The quick start mode offers a streamlined application usage experience. It reduces track settings to facilitate quicker navigation.

      • In quick start mode, the selection of fields, patterns, tasks, work areas, and U-turn settings is not necessary to initiate navigation. This mode is advisable for new users and those utilizing the free version of the application.

      • By default, the quick start mode is DISABLED.

      • To Activate , Go to Settings > Select Quick Start mode

      Quick Start Mode Activation - Settings.png

      Fig.14.13 - Sound/Voice Alert Setting Screen

      • Click Activate

      Quick Start Mode activation.jpg Fig.14.14 - Sound/Voice Alert Setting Screen

      • To Use Quick Start Mode user needs to Provide
        • Vehicle Details,
        • Implement Details,
        • Guideline.

      Quick Start Mode - Navi Screen.jpg Fig.14.15 - Sound/Voice Alert Setting Screen

      • To Deactivate Quick start mode Tap IconQuick Start mode - Icon.PNG & Click Deactivate

      Quick Start Mode deactiavte- Navi Screen.jpg

      16.3. GPS settings

      The GPS settings offer configuration options for tracking location and assessing signal quality.

      • You have the ability to set the GPS location within the vehicle, modify the GPS frequency, and activate the GPS Quality Filter to enhance positioning accuracy.
      • This filter accommodates multiple GPS correction techniques, such as GPS, DGPS, FRTK, and RTK, thereby guaranteeing accurate navigation and location tracking.

      GPS Settings.png Fig.14.16 - GPS Setting Screen

      16.3.1. GPS frequency.

      • GPS frequency, commonly referred to as the GPS refresh rate, indicates the frequency at which a GPS receiver refreshes its location data each second. This is quantified in Hertz (Hz), where 1 Hz signifies that the GPS updates once every second, while 5 Hz indicates five updates per second.

      • The default value is 5Hz.

      GPS Frequency.jpg Fig.14.18 - GPS Frequency Settings

      info-alert.png
      Note: An increased GPS update frequency offers enhanced real-time positioning; however, higher frequencies may also lead to greater power consumption and elevated data processing demands.

      16.3.2. GPS quality filter.

      The GPS Quality Filter is a functionality designed to enhance the precision and dependability of GPS data by eliminating inferior quality signals. It guarantees that only GPS data that satisfies particular accuracy criteria is utilized, thereby minimizing errors resulting from weak or unstable signals.

      GPS Quality filter.jpg Fig.14.19 - GPS Quality Filter

      1. GPS (Standard GPS): Fundamental satellite positioning with lower accuracy (approximately 5-10 meters).

      2. DGPS (Differential GPS): Improved accuracy achieved through correction data (around 1 meter).

      3. FRTK (Float RTK): Medium-precision Real-Time Kinematic positioning (approximately 10-30 centimeters).

      4. RTK (Real-Time Kinematic): High-precision positioning (about 1-2 centimeters).

      info-alert.png
      Note: By default, ALL (GPS, DGPS, FRTK, RTK) signal quality levels are utilized for navigation.

      16.3.3. Control of the Working Area (10.9.x).

      In the FieldBee application, you possess the ability to determine how your working area is documented. By default, the application computes coverage based on the Field Boundary. Nevertheless, depending on your particular task or equipment configuration, you can modify this functionality in the settings to guarantee the most precise data for your agricultural records.

      To adjust how your area is computed, proceed to the system settings:

      • Launch the FieldBee app and select the Menu icon (three horizontal lines) located in the top-left corner.

      • Choose Settings from the available options.

      • Scroll down to the Navigation section.

      • Select Control of the Working Area.

      Select the method that aligns with your workflow:

      • By Field Boundary (Default): The area is automatically calculated as soon as the tractor enters the designated field boundary. Recording ceases when you exit the boundary.
      • By Autosteer Engagement: The area is calculated solely when Autosteer is engaged. This option is optimal if you wish to ensure that coverage is recorded only while the system is controlling the tractor's steering.
      • Off: Automatic calculation is disabled. You are required to manually switch the implement on or off to record the area.

      Tap Save to implement the changes.

      17. ISOBUS

      ISOBUS- Kit.jpg

      The standard Jaltest i-Connect kit is a complete solution that enables agricultural equipment to work with any ISOBUS agricultural implement. The installation must be fully integrated in the agricultural equipment to ensure the comfort of the farmer. The product is compatible with any type of agricultural equipment regardless of the brand and model.

      Universal Terminal Task Control
      ISO bus.jpg Task control.jpg

      17.1. Jaltest ITC Integration Guide (ISOBUS, Cojail)

      The integration of Jaltest ITC converts your FieldBee tablet into a Universal Terminal (UT) and Task Controller (TC). This facilitates smooth communication between your tractor and different implements, allowing for functionalities such as automatic section control and variable rate application.

      Activate the Integration

      To begin, it is necessary to establish the connection between the FieldBee application and the Jaltest ITC software.

      1. Launch the FieldBee app on your tablet.
      2. Click on the Menu icon (three horizontal lines) located in the top-left corner.
      3. Choose Settings from the side menu.
      4. Scroll down to the ISOBAS section.
      5. Press on Link to Jaltest ITC.
      6. A pop-up window titled "Link to Jaltest ITC" will appear. Examine the features and click the Turn on button at the bottom.

      17.2. Set Up Split-Screen Mode (Kcosit Tablet / Android 9)

      Setting up Split-Screen

      To manage your navigation while simultaneously implementing controls, adhere to the following steps to activate split-screen mode:

      1. Launch your Applications: Confirm that both the FieldBee app and the Jaltest ITC app are actively running.
      2. Open App Switcher: Press the Home button twice. A horizontally scrolling list of your active applications will be displayed.

      Tablet Home Button image.PNG

      Choose Split Mode: Locate the FieldBee application within the list.

      • Press and hold the app icon located at the top of the preview window.
      • A new menu will be displayed; select the Split screen icon

      ISOBUS -Take Recovery Screen.png

      ISOBUS - Splitup screen.png

      Select the Second Application: The display will be split. Choose the Jaltest ITC application from the available options to show it in the second portion of the screen.

      ISOBUS - Setup screens.png

      Adjust: You are now able to utilize both applications simultaneously.

      17.3. Initiating and Coordinating Tasks

      Prior to commencing field operations, verify that both systems are correctly configured and synchronized to facilitate accurate implement control.

      17.3.1. Pre-Operation Checklist

      Prior to launching the Jaltest application, it is essential to carry out the following preparatory steps within the FieldBee application:

      • Input Vehicle Parameters:
        • Measure and record the distance from the rear axle to the 3-point hitch.
        • Measure and record the distance from the rear axle to the drawbar or towed hitch.
        • Field Configuration: Confirm that you have previously established the field in which you plan to operate.

      17.3.2. Creating New Task

      Once the parameters of your vehicle are configured and Jaltest communication is activated, please adhere to the following steps to initiate a task:

      1. Access Navigation: Within the FieldBee application, select the Add (+) button to establish a new task.
      2. Choose Task Type: Identify your operation (for instance, Tilling, Spraying, Fertilizing, or Planting).
      3. Select Field and Vehicle:
      • Designate the necessary Field for the operation.
      • Select the Vehicle profile (for example, Case 5130) that has been previously set up.

      17.3.3. Synchronizing Data with Jaltest

      When both the field and vehicle are chosen, the synchronization option is enabled:

      1. Share Data: Press the SHARE DATA button located in the Jaltest ITC status box.
      2. Automatic Implementation: Following synchronization:
      • The relevant ISOBUS implement (for instance, SPRAYER - Cojali S.L.) is automatically generated in the FieldBee application.
      • The corresponding operation is concurrently established within the Jaltest application.

      17.3.4. Navigation

      1. Press the Start (Yellow Arrow) button in FieldBee to initiate navigation.
      2. Active Tracking: After initiation, tracking recording commences concurrently in both applications, enabling you to oversee navigation in FieldBee while handling implement data in Jaltest.

      18. Navigation Grid

      We have created an innovative Navi Grid layout that offers enhanced graphics, quicker rendering, and improved performance in the field. This layout enables operators to easily visualize vehicle locations, field boundaries, and guidance lines.

      18.1. How to enable the Navi Grid feature (from 10.8.x)

      info-alert.png
      Note: In 10.8.x Navi Grid layout avalible only in Navigation mode.

      Activating Navi Grid

      1. On the top bar, tap the Layout icon Map Layer icon.png
      2. From the list of layouts, select Navi Grid.

      Navigation Grid Selection.jpg

      Preparing for Navigation

      1. Complete all necessary Track Parameters (Vehicle, Implement, U-Turn Params, Headland Params, Pattern Params).
      2. After the parameters have been configured, press Start to initiate navigation with the Navi Grid.

      18.2. Navigation on Navi Grid layout

      Navi Grid – Main Layout

      Upon selecting Start Navigation, the system presents the main Navi Grid layout. The background is rendered as a grey grid, indicating your vehicle's position and the field boundary.

      We have enhanced the Navi Grid and incorporated new features to provide clearer and more adaptable navigation:

      18.3. Key Functions

      1. Zoom Control
        • The Navi Grid now allows zoom down to 0.1 m.
        • This provides very precise view when working with narrow implements or detailed field operations.
      2. Notes on Map
        • In Navigation mode, you can now set Notes directly on the map on current location.
        • This helps mark important points (e.g., obstacles, field issues, start/end points).
      3. Center Button Improvements
        • The Center button has been enhanced with two modes:
          1. 2D Mode (default): The layout follows the navigation marker from a top-down view.
          2. 3D Mode: Tap the button again to switch to a 3D perspective, providing a better sense of heading and field orientation.
      4. Kompass
        • It helps you understand your current orientation relative to the Earth.
        • The Kompass shows the north direction, making it easier to align your position in the field.
      info-alert.png
      Note: Use the Kompass together with the 3D view to quickly check both your heading and field orientation

      Navigation grid working screen.png

      19. Technical Specifications

      I. Steering Motor (PowerWheel)

      Feature (Functionality) Specification (Parameter) Detail (Key Metrics)
      Peak Torque 15 N*m (Max) High peak torque for fast steering correction.
      Rated Torque 7 N*m Consistent working torque.
      Speed/Response 80–100 rpm High rated rotation speed.
      Peak Current 20 A Instantaneous power for demanding maneuvers.
      Protection Rating IP55 Protection against dust and water jets.
      Operating Temp. -25 C to +55 C Reliable operation in harsh field conditions.
      Control Signal RS232 / CAN 2.0 Standardized control interfaces.

      II. ALL IN ONE CONTROLLER

      Feature (Functionality) Specification (Parameter) Detail (Key Metrics)
      Precision (RTK Accuracy) 2.5 cm Consistent sub-inch accuracy for all field operations.
      Speed Range 0.2–22 km/h Wide operating speed range.
      Terrain Compensation +/-15 deg, accuracy 1 deg Full roll/pitch compensation for accurate work on slopes.
      GNSS Constellations GPS L1C/A L2C, GLO L1OF L2OF, GAL E1B/CE5b, BDS B1I B2I, QZSS L1C/A L2C Supports GPS, GLONASS, Galileo, BeiDou, QZSS.
      Protection Rating IP67 Fully protected against dust and immersion (ideal for external mounting).
      Operating Temp. -20°C to 85°C RoHS, CE, ISO 15003 Extremely wide operating temperature range.
      Communication Wi-Fi, LoRa, CANopen, J1939, Socket NMEA 01839 Full connectivity suite including CAN Bus compatibility.

      III. PowerTablet and Docking Station Specs

      Feature (Functionality) Specification (Parameter) Detail (Key Metrics)
      Tablet Display 10 inch HD (1280 x 800) 1000 cd/m high brightness, sunlight readable.
      Tablet RAM/Storage 2 GB RAM Standard configuration for reliable performance.
      Battery 3.7V, 8000mAh Li-ion (Repleacable) Battery operating time: about 4.5 hours.
      Tablet Protection IP65 (with supplied dock) Protection against dust and water.
      Docking Ports Type-C, Compliant with USB (For data transfer, support OTG) Connectivity for peripherals and data transfer.
      Docking Bus Ports USB2.0 (Type-A) - x1, RS232 - x2, Docking Station Status - x1, ACC - x 1, Power - x1, Canbus For advanced tractor integration.

      IV. PowerSteer System (Product Overview & Physical Specs)

      Feature (Functionality) Specification (Parameter)
      System Accuracy 2.5 cm
      Vehicle Compatibility Fits front-wheel steer tractors, rear wheel steercombine harvesters, self-propelled sprayers, and open-cabin tractors.
      ISOBUS Compatibility CAN 2.0 (J1939, NMEA 2000)
      Product Protection IP67 (Controller), IP55 (Motor)
      Operational Speed 0.2–22 km/h
      Installation Time < 1 hour
      Supply Voltage (Rated) 9–32V DC
      Peak System Consumption 20 A
      Controller Dimensions diameter 150 mm* 75 mm
      Motor Dimensions diameter 171 mm* 65 mm
      Steering Wheel Dimensions diameter 400 * 50 mm

      20. Additional Tools Tips

      • Quick Sync in Field: Use Quick or Custom sync.
      • Autosteer Logs: Send manually via Settings.
      • Navi Grid: Best for narrow implements.
      • Reverse Recognition: ,.