Skip to main content

Manual Freeplay Calibration (Deadband) (from 10.10.1)

Freelpay calibration determines the minimum steering angle at which the front wheels start to move. This value must be measured and then saved in the tractor parameters.

Preparation

 

Before starting calibration:

  1. Warm up the engine and hydraulic system.
    The hydraulic steering system must be operating under normal conditions.
  2. Park the tractor on a flat surface.
  3. Straighten the front wheels.
  4. Exit the cabin and stand near the front wheels so you can clearly see the moment when they begin to move.
# How to Perform Manual Freeplay Calibration

This article walks you through calibrating the steering freeplay angle for a PowerSteer-equipped vehicle from the My Equipment screen.

Before you start

⚠️ Safety first. Freeplay calibration involves moving the steering wheel while standing outside the vehicle. Complete every item below before you begin.

    Warm up the engine and hydraulic system. Position the wheels straight ahead. Check that the area around the vehicle is clear of people and obstacles. Exit the vehicle and remain outside the cab. Keep a safe distance from the vehicle while calibration is running.

    Safety instructions dialog

    Step 1: Open your equipment

    1. Go to My Equipment.
    2. Select the connected PowerSteer device from the list on the left (status shows CONNECTED).
    3. In the calibration list on the right, find Manual Freeplay Calibration and tap the arrow to open it.

    My Equipment screen with connected PowerSteer device

    Step 2: Confirm the safety checklist

    A Safety instruction for Freeplay Calibration dialog appears, listing the five safety steps above.

    • Read each item carefully.
    • Once the vehicle and area are ready, tap Proceed to Calibration.
    • If you're not ready, tap Cancel and return once conditions are met.

    Step 3: Review the calibration overview

    The Manual Freeplay Calibration screen opens, showing:

      The selected vehicle (e.g., vehicle 1) The five safety steps as a reference checklist on the left A diagram of the vehicle on the right A Why do you need to do calibration? link if you want more background

      Tap START to begin.

      Manual Freeplay Calibration overview screen

      Step 4:3: Adjust the freeplay angle

      The screen switches to the live adjustment view, showing a close-up of the front wheel and steering linkage alongside a reminder to keep a safe distance from the vehicle.

      1. Use the + and − buttons next to Freeplay angle to change the value in small steps.
      2. Valid range: 0.5° – 45.0°.
      3. Stop as soon as the front wheels make a small twitch — not a full turn. This twitch marks the edge of the mechanical freeplay.
      4. Once you're satisfied with the value, tap FINISH.

      Adjusting the freeplay angle

      💡 Tip: Increase the angle gradually and watch the wheels closely — overshooting past the twitch point means the value is too high and no longer reflects true mechanical freeplay.

      Step 5:4: Respond to a high freeplay angle warning (if shown)

      If the value you set reaches 25° or higher, the app flags it as outside the typical range:

      High freeplay angle value The value you've set is 25° or higher — this is outside the typical range and may indicate an older tractor generation or a mechanical issue with the steering system. We recommend contacting service before continuing.

      You have two options:

      • RECALIBRATE — go back and lower the angle to a value inside the typical range.
      • SAVE ANYWAY — accept the high value and continue (only do this if you understand why the value is high, e.g., a known older tractor generation).

      High freeplay angle warning dialog

      Step 6:5: ReviewCalibration the completion screen

      completed!

      Once calibration is saved, a confirmation screen shows:

      • Calibration completed!
      • The vehicle name (e.g., vehicle 1)
      • The final Freeplay angle value — flagged with a warning icon if it's still outside the typical range

      From here you can:

      • Tap RECALIBRATE to redo the process and adjust the angle again.
      • Tap GO TO MY EQUIPMENT to finish and return to the equipment list.

      Calibration completed confirmation screen

      Summary

      Step Action 1 Open the vehicle in My Equipment and select Manual Freeplay Calibration 2 Read and confirm the safety checklist 3 Review the overview screen and tap START 4 Adjust the freeplay angle with +/− until the wheels twitch, then tap FINISH 5 If prompted, choose RECALIBRATE or SAVE ANYWAY for high values 6 Review the completed calibration and exit to My Equipment

      Note on this article: The source video's spoken narration could not be reliably transcribed by the automated speech-to-text process available in this environment, so this manual was built from a frame-by-frame visual analysis of the on-screen workflow instead. On-screen text and values (e.g., the exact freeplay angle progression) are accurate; if the narration included details not visible on screen, they may not be captured here. Let me know if you'd like me to try transcription again with a supplied transcript, or refine any section.