Wi-Fi Configuration

1. Introduction

Welcome to the Hostpot Device Configuration user guide for Autosteering system. This manual describes how to install, set up Hotspot devices, and use the application.

1.1 General Warning

Sign	Safety Instruction
	Always read the full documentation before installing or operating the PowerSteer system. Failure to follow safety precautions may lead to injury or damage.
	NEVER leave the operator's seat with the system engaged. This prevents accidental death or injury from the vehicle running over someone. A person must always be present in the operator's seat.
	Verify the area is CLEAR of people and obstacles before startup, calibration, tuning, or use of the system.
	DO NOT operate on public roads or in public areas; power down the system while driving on them. Powering up the system on public roads can cause accidental engagement and loss of vehicle control.
	The operator is responsible for safe driving at all time.
	The system does not detect obstacles.
	The system does not control vehicle speed; the operator must manually adjust speed to maintain control.

1.2. Installation Safety and Environment

Sign	Installation & Safety Guidelines
	DISCONNECT power (power OFF) before installing, removing, or performing maintenance on any connected components.
	Ensure components are installed firmly. Improper installation may cause machine damage and poor performance.
	Use a ladder to access vehicles Roof Safety when Insatlling the steering controllerto prevent falls
	Avoid extreme environments: Do not install in environments with high temperature, heavy dust, harmful gases, flammables, explosives, great vibration, or strong noise.
	Protect against water: Do not install the equipment in places vulnerable to water accumulation, seepage, dripping, or condensation, as this could damage the ports.<
	Keep away from interference: Stay away from high-power wireless equipment, such as radar stations, transmitting stations, and substations, to avoid electromagnetic interference.
	Do not frequently disassemble the equipment after installation to avoid accidental damage.

1.3. Electrical and Mechanical Safety

Sign	Electrical & Installation Safety Guidelines
	Electrical operations must be performed by qualified personnel.
	CRITICAL PRE-CHECK: Verify all screws, bolts, nuts, and cable connections are tight before operation. Ensure all cables are secured to prevent damage.
	Cable Routing (CRITICAL): DO NOT route cables over hot surfaces (e.g., engine block, exhaust) or near sharp/rotating parts (e.g., shafts, fan blades) to prevent melting, fire, tearing, or short circuits.
	Unpredictable Movement Warning: Vehicle steering axles, tracks, or wheels may move unpredictably during testing or calibration. Ensure no people or obstacles are near the wheels during these stages.
	Power Connection: Connect the negative terminal first, then the positive terminal.
	Hydraulic Caution: Relieve hydraulic pressure before starting service if installation involves the hydraulic system.
	Wear hand and eye protection during installation.

1.4. Legal and Operational Compliance

Mandatory Disengagement: It is critically important for the Manual Steering Override (Kickout) feature to be functioning and set to the proper level to allow the user to disengage AutoSteer manually. Never operate an AutoSteer system without this feature working or set properly.
Liability Disclaimer: Manufacturer disclaims any liability for damage or injury that results from failure to follow instructions, cautions, and warnings set forth herein, or as a result of operator actions that fall outside the recommended application.

1.5. Download Fieldbee Link Application

For Downloading FieldBee Link application , User will be provided with apk file during Purchase.

	Information : This Application will Not Available in Playstore

1.6. Download Fieldbee Toolbox Application

Downloading Fieldbee Toolox can be done by using Google Playstore

Search FieldBee Toolbox in Playstore

	Information : Latest Version can be Downloaded at Google Playstore

2. Base Station Configuration

In this Section ,

Configuration of Base Station were Learned ,

Hotspot Device Wi-fi Credentails Configuration
Base Station Set to Service Mode
Base Station Configured to Hotspot Device Wi-fi Credentials

	Information : For Base Station Configuration Required Both Fieldbee link & Fieldbee Toolbox Application

2.1. Step-1 : OFFBoard Device Switch ON

Switching ON the OFFBoard Device

Device Switch ON Condition

2.1.1. LED Status Indications

LED Status of the Device After 30 Secs from Start-up

Device LED Status

2.2. Step-2 : Open Fieldbee Link Android Application

	Information : After Opening Application , Enable Location & Bluetooth for Scanning devices

2.3. Step-3 : Scan for Device

Click Scan to find the near by devices

	Information : If device not Listed , Scan again to find the device

	Information : If Multiple Devices listed , Select the required device to view status & configuration

2.4. Step-4 : Wi-Fi Credentails Configuration

	Information : User can change the User Name & password for connecting the devices

To Configure the Wi-Fi Details
- user can Setup the user name under SSID tab
- user can setup the password under Password tab

After Configuration click Configure WiFi to configure

Next , Click Reboot to update the Wi-Fi Credentails

Next Step is verifcation.

2.4.1 : Verifcation After Configuration

	Information : After configuration were updated , Connect to updated Wi-Fi Credentail

Select the Device and Check for Wi-fi Credentails under Information menu

2.5. Step-5 : Base Station - Set to Service Mode

To Set the base Station to Service Mode , Hold the Power button for more than 15 Seconds ( Until Fast Blink Apprears )

Switch ON Wi-fi in Tablet Check for Wifi Network Name Starting with FieledBee.....

Connect to the Wifi Network Name Starting with FieledBee.....

2.6. Step-6 : Connecting to Base Sation in Toolbox

	Information : Open Fiedlbee ToolBox for Configuring Base Station

Open Toolbox & Select RTK Base Station

Connect to the Base Station (in Service Mode)

2.7. Step-7 : Base Station Wifi Credentials configure to OFFBoard Device Network

After Connecting to the Base Station
Go to Wi-Fi Menu & Configure the Credentails

Change the Wi-Fi Credentails as per OFFBoard Device Wi-fi Credentails

After that , Click Set to Apply the Credentials

Click Reboot to Complete the Process.

	Information : Now Base Station is Configured with OFFBoard Hotspot Device

	Information : Connect to OFFBoard Device Wi-Fi Network to See Base Station Details using Toolbox

3. Receiver Configuration

In this Section ,

Configuration of Receiver were Learned ,

Hotspot Device Wi-fi Credentails Configuration
Receiver Connection
- Set to Factory Set Mode ( if Wi-fi Credentails Forgot )
Receiver Configured to Hotspot Device Wi-fi Credentials

	Information : For Receiver Configuration Required Both Fieldbee link & Fieldbee Toolbox Application

3.1. Step-1 : ONBoard Device Connection

Connect the Wiring Harness as per the Below Image

3.1.1. LED Status Indications

LED Status of the Device After 30 Secs from Start-up

Device LED Status

3.2. Step-2 : Open Fieldbee Link Android Application

	Information : After Opening Application , Enable Location & Bluetooth for Scanning devices

3.3. Step-3 : Scan for Device

Click Scan to find the near by devices

	Information : If device not Listed , Scan again to find the device

	Information : If Multiple Devices listed , Select the required device to view status & configuration

3.4. Step-4 : Wi-Fi Credentails Configuration

	Information : User can change the User Name & password for connecting the devices

To Configure the Wi-Fi Details
- user can Setup the user name under SSID tab
- user can setup the password under Password tab

After Configuration click Configure WiFi to configure

Next , Click Reboot to update the Wi-Fi Credentails

Next Step is verifcation.

3.4.1 Verification After Configuration

	Information : After configuration were updated , Connect to updated Wi-Fi Credentail

Select the Device and Check for Wi-fi Credentails under Information menu

3.5. Step-5 : Connecting to receiver in Toolbox

	Information : Open Fiedlbee ToolBox for Configuring Receiver

	Information : By Default , Wi-fi Credentials will be rtkwifi and 12345678

Switch ON Hotspot in Tablet

Next , Check for device Connected.

After Device Connected
Open Toolbox & Select PowerSteer

Connect to the Receiver

3.5.1. Wi-Fi Credentail Reset - In Case of Forgot

In Case of User Forgot Wi-Fi Credentials of receiver , user can reset the Wi-Fi Credentails to factory set .
To factory set the Receiver , Hold the Power button for more than 15 Seconds (Until Fast Blink Apprears )

After this , Process from Step-5

3.6. Step-6 : Receiver Wifi Credentials configure to ONBoard Device Network

After Connecting to the Receiver
Go to Wi-Fi Menu & Configure the Credentails

Change the Wi-Fi Credentails as per ONBoard Device Wi-fi Credentails

After that , Click Set to Apply the Credentials

Click Reboot to Complete the Process.

	Information : Now Receiver is Configured with ONBoard Hotspot Device

	Information : Connect to ONBoard Device Wi-Fi Network to See Receiver Details using Toolbox

4. Hotspot Device factory set Configuration

In case of user forgot the ONBoard & OFFBoard Device Credentials , it can be set to factory set Wi-Fi Credentials
To Do Factory set
Select the device > Configuration
Click Restore to do Factory set.

After that , Click Reboot to Complete the process

	Information : Updated Wi-Fi Credentails can be seen on Wi-Fi Informations screen

5. OFFBoard Device Charging

To Charge the OFFBoard Device

First Switch ON the OFFBoard device
Connect the Charging Pin for Charging.

	Information : Without Switching On the Device , Device wont Start Charging even Charging port is pluggedIn